Poop Chute & Basket & Accessory holder by Rober7Crow

Rober7Crow

3D Printer>3D Printer Accessories

GIF

Print Profile(2)

All

X1 Carbon

P1S

P1P

X1E

0.2mm layer, 2 walls, 10% infill

Designer

44.2 h

11 plates

4.9(67)

Fuzzy skin as in the photo 0.2mm layer, 2 walls, 10% infill

Designer

103.6 h

11 plates

5.0(2)

Open in Bambu Studio

Boost

235

393

156

564

306

Released

Description

I had to get a bit organised and tidy up around the printer. I was looking for something handy and to come as a set. I couldn't find anything that combined several elements together. So I decided to make something myself that would help me and keep the essentials handy.

As I have Anti vibration feet on the printer I worked in that direction and then prepared the original feet.

Since I always buy the wrong magnets and screws, I worked in this direction so that we don't need anything else but a printer and filament :)

Please choose the right components from the printer profile. See below for a picture of what it contains:

Please choose the right one according to the base you are using

A few more possible setups :)

Small Basket

Medium Basket

Big basket

Comment & Rating (156)

@hitechuno

Print Profile

0.2mm layer, 2 walls, 10% infill

printed out really well and was the best model that I could find which was modular to meet most of my needs. A few minor issues but I suspect these are more due to how the app (I printed from the bambu handy app) placed some of the plates with the item hanging a little off the edge (see photos). I printed using the Bambu pla basic black.

The designer has replied

@Rober7Crow

Thank you for these beautiful pictures, I love this color combination. I myself am thinking in three colors - black/grey/white, like most of my creations, but then I only decided on two colors 🤗

@hitechuno

Replying to @Rober7Crow :

agree sometimes black and white is best! I decided not to print the tray with the logo (although I wanted to) to save on color changes and poop but did it on the poop basket. As a suggestion if you could make the ‘max’ line a separate piece which clips over the basket it would save a lot of time and filament changes? I’m just starting to dip my toe into the slicer etc so haven’t tried any remixes or mods on any models yet

@Rober7Crow

Replying to @hitechuno :

You also can print just in one color, just delete white filament. I am thinking more about including drawers and a filament spool holder in this set.

(Edited)

@user_660532803

I remodeled the basket so I could attach a removable lock-in-place Red Wings logo. Both pieces printed great!

The designer has replied

@Rober7Crow

nice works 🤗

@chg22

Print Profile

0.2mm layer, 2 walls, 10% infill

Printed smoothly without support, and was fast. The chute also fit perfectly with my P1S.

The designer has replied

@Rober7Crow

nice print thanks for sharing the photo

@Steelmen

Did anyone notice that the files with the anti-vibration feet raise the left side of printer, which causes it to be a little uneven and not level. Any thoughts on this or if will be an issue? I did notice a little "wobble". Thanks

The designer has replied

@Rober7Crow

Depends how high you have the anti-vibration feet, I use the ones in the picture below and no problems. In your place I would prefer to pad the rubber bands so that the printer can breathe better

@Steelmen

Replying to @Rober7Crow :

Did you print those feet or purchase them?

@Rober7Crow

https://a.aliexpress.com/_ExmuLv1

@user_3589171013

Boosted

Print Profile

0.2mm layer, 2 walls, 10% infill

no issues printing other than I ran out of green during print and had to switch to blue. Works great.

The designer has replied

@Rober7Crow

Thank you for sharing the photo 🤗

@sara_savage

Print Profile

0.2mm layer, 2 walls, 10% infill

Filament used: Inland PLA + in Gray Bambu Basic PLA in Bambu Green

(Edited)

The designer has replied

@Rober7Crow

Thanks for sharing the photo :)

@user_3836306908

Boosted

this is a good fit and super handy to dump.

The designer has replied

@Rober7Crow

Thank you for sharing the photo 🤗

@JMHS_BKLYN

Print Profile

0.2mm layer, 2 walls, 10% infill

Came out great! Wish more modules were available. But great overall.

The designer has replied

@Rober7Crow

I'll make more additions just to get to the free time :)

@FoSsiLzA

Print Profile

0.2mm layer, 2 walls, 10% infill

This is awesome

(Edited)

The designer has replied

@Rober7Crow

Thank you for sharing the photo 🤗

@Moarti

Print Profile

0.2mm layer, 2 walls, 10% infill

A little bit stringy at one of the overhangs but only a little bit and the rest of it came out so nice I didn’t think it was worth taking off a star

The designer has replied

@Rober7Crow

Yes this overhang is really tricky, I was trying to draw it to make it as easy to print as possible. Thanks for the 5 stars :)

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.