Bambu Poop bucket box by 3D Schoko

3D Schoko

3D Printer>3D Printer Accessories

Print Profile(3)

All

X1 Carbon

P1S

P1P

X1E

43mm Version 0.2mm layer, 3 walls, 15% infill

Designer

7.3 h

1 plate

4.4(51)

53mm Version 0.2mm layer, 3 walls, 15% infill

Designer

7.9 h

1 plate

4.2(22)

43mm

7.3 h

1 plate

5.0(1)

Open in Bambu Studio

Boost

112

145

125

895

531

Released

Description

Poop box for Bambu Lab printers.

Important: This waste bin only fits under the waste chute if the printer is on an additional plate. Please look at the image for dimensions and check the height before printing.

2 versions:

43mm: For thinner granite slabs with a rubber mat.

53mm: For thicker concrete slabs.

It can be printed without support.

Update 12/31/23: Stl. file edited for smooth radius.

There is also a smaller version just for the back.

https://makerworld.com/en/models/26855#profileId-35078

And another simple trash can without the cutout for records.

https://makerworld.com/en/models/51331#profileId-53111

Comment & Rating (125)

@speedyone66

Print Profile

53mm Version 0.2mm layer, 3 walls, 15% infill

printed very well and accurately molded around my X1 carbon just had to dremel the part where the poop shute is. im very new to printing but im assuming that part of it was left for ease of print ,and not a big deal to remove it

(Edited)

The designer has replied

@Schoko

Don't you have a plate under the printer? How thick is it? For a granite slab with a rubber mat I get a height of 40mm. The low version of 43mm is sufficient up to the radius. For thicker concrete slabs, the 53mm version they printed is recommended.

@speedyone66

Replying to @Schoko :

no its just sitting on a wooden table

@Schoko

Replying to @speedyone66 :

OK. That's the problem. The trash can is only intended if there is a plate underneath. That's why it has the recess on the sides. I wrote my profile text differently so that it can be better understood.

@msa1906

Print Profile

53mm Version 0.2mm layer, 3 walls, 15% infill

not fit for p1s. need cut part for fitting p1s

(Edited)

The designer has replied

@Schoko

Hello, what exactly shouldn't fit? Do you have a plate under the printer?

@Schoko

Replying to @Schoko :

Yes, they do not have an additional plate under the printer. But everything is in the description.

@Teixeira_3d_hom

Print Profile

43mm Version 0.2mm layer, 3 walls, 15% infill

model to high for x1c

The designer has replied

@Schoko

The model cannot be too high if it is used as intended. Read discription!

@kyle.mattfield

Replying to @Schoko :

The description leaves a lot to be desired. I'm guessing "plate under the printer" is some modification that involves a solid plate directly under the printer. Without knowing this is what you are talking about nobody would know that is the purpose, or even that adding a plate under the printer (and only under the printer) is even a thing. You may also want to add a design that is just for the printer sitting on a desk since that is how most will use it.

@Schoko

Replying to @kyle.mattfield :

I don't understand what you don't understand about the description. Maybe because it is translated with Google. It's not uncommon to have a plate under the printer, many people have it, and if you look at the photos you can see that the printer is on a plate. In addition, the poob box has a cutout for this, what else would it have a cutout for? From the photos alone you can already see where it is intended. And there is also a photo with dimensions where you can measure it before printing.

@GodzillaDoodle

Print Profile

43mm Version 0.2mm layer, 3 walls, 15% infill

too tall for my p1s by at least 1-2cm

(Edited)

The designer has replied

@Schoko

Danke, das freut mich

@ZR_CrackiiN

needs more benchies

@dennis.day.58

Print Profile

43mm Version 0.2mm layer, 3 walls, 15% infill

I like how it has a higher back where the poop pellets come out of the printer as the previous one it tried a lot of poop went over the back and fell on the ground.

@Smart3dpt

Print Profile

53mm Version 0.2mm layer, 3 walls, 15% infill

The designer has replied

@Schoko

I see that they don't have a plate under the printer and have still printed the high version. The trash can is specifically designed for when a disk is under the printer.

@user_289720177

Print Profile

43mm Version 0.2mm layer, 3 walls, 15% infill

@uwebueger

Print Profile

43mm Version 0.2mm layer, 3 walls, 15% infill

Die Box muss im Bereich des auswurfschachtes ausgeklinkt werden.Die Box ist 20mm zu hoch.

The designer has replied

@Schoko

Die Box passt ganz genau. Wenn man ein Platte unter dem Drucker hat. Sie sollten mal die Beschreibung lesen. Da steht es groß und Fett das die Box nur dann unter den auswurfschacht passt. Und ein Bild mit Maßangaben ist auch dabei um vor dem Drucken es zu überprüfen.

@uwebueger

Oh sorry das hab ich übersehen. Aber sehr schönes design.

@jropp3

Print Profile

43mm Version 0.2mm layer, 3 walls, 15% infill

to tall for my shoot but it works after i modified it

(Edited)

The designer has replied

@Schoko

The box doesn't fit without an additional plate.

@jropp3

i am sorry i did not read that is my fault i will see if i can change the rating for you

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.