Adjustable BooKoo Coffee Electric WDT
Remixed by
Copyright Claim
Adjustable BooKoo Coffee Electric WDT
Remixed by
Boost
19
36
29
Print Profile(1)
0.16mm layer, 3 walls, 10% infill
Designer
4.5 h
1 plate
Open in Bambu Studio
Boost
19
36
29
2
140
65
Released
Description
Thanks to the innovative design of bookoo, modifications have been made on the basis of the original model:
1. Fine-tune the dial to make it able to fit the hot bed printing
2. Adjust the dial to be rotatable for convenient adaptation to different heights
At the same time, slice optimization is carried out for different components to significantly reduce printing time and printing consumables while ensuring the use effect.
Comment & Rating (29)
All
The adaptive height is really useful the only thing is the needle holes are big.
The designer has replied
0
Reply
Thank you for your feedback. You can fine tune the xy hole compensation for the needle disk. Currently, I have set it to+0.1
1
Reply
Replying to @bladow_kb
不是孔太大了吗？为啥要+0.1？？？？
0
Reply
Replying to @acwell
目前我上传的切片设置是+0.1
0
Reply
作者你好，我根据你的模型改装了一个适用于delonghi；51mm/EC680/EC685/EC885的版本，并且与bambulab中的电动套件完全适配。我可以获得你的授权后在此网站中，发布模型吗？可以吗？
The designer has replied
0
Reply
能不能分享下？我用的就是德龙的。看作者的许可，是可以二次创作的，
0
Reply
当然可以， 欢迎分享
0
Reply
Print Profile
0.16mm layer, 3 walls, 10% infill
Auf einen 57mm Siebträger passt es leider gar nicht. viel zu groß.
Stützen sehr schwer zu entfernen.
0
Reply
Print Profile
0.16mm layer, 3 walls, 10% infill
A great tool! My only problem was the button, I had to glue it to keep it in place.
0
Reply
Print Profile
0.16mm layer, 3 walls, 10% infill
the holes are slightly to big up top and then slightly too small on bottom, I could force the needles in but I damaged 1 putting it together. needs to have 1 size hole and be snug, so it can be adjusted that way as well
(Edited)The designer has replied
0
Reply
whoa whoa
(Edited)1
Reply
Replying to @ouijaboux
fixed it 😂😂
0
Reply
You can fine tune the xy hole compensation for the needle disk.
0
Reply
非常感谢这次修改。不用支撑打印可以避免原模型支撑面不太好看，以及支撑面残留导致旋转不均匀的问题。另外，大齿轮部分平面代替原来的斜面，也避免了上盖配合度导致的挤压问题。
The designer has replied
0
Reply
这个模型也存在很多问题，螺纹应该是没有设计公差，实用性差。螺纹感觉设计的太密，打印难度大。
0
Reply
Replying to @acwell
您使用了我的打印配置也存在这个问题吗？我针对针盘特意降低层高至0.16并降速、扩大了xy补偿。因为材料不同，收缩率不同，如果还出现调节不顺情况，可适当调节针盘的xy补偿，同时针盘速度降到60，层高降为0.12。
0
Reply
Replying to @bladow_kb
最近我又用K家PLA K5打了一下，尺寸问题不大，除了小孔。上次问题出现在sunlu的PETG。
0
Reply
I would love to see a 51mm and 54mm version! thanks for sharing!
The designer has replied
2
Reply
I'm sorry I don't have a 51 or 54, but someone else has modified and produced a new model based on my design. You can check out their design
0
Reply
Great remix, make this a lot easier to print. Can you modify the main body to require less supports?
The designer has replied
0
Reply
It's a bit difficult to modify the main body, but I can try
0
Reply
想问一下大家电子件 跟 五金件怎么买到的
0
Reply
Boosted
Print Profile
0.16mm layer, 3 walls, 10% infill
Perfect remix, exactly what I needed
0
Reply
This remix is based on
License
This user content is licensed under a
Creative Commons Attribution-Noncommercial-Share AlikeRemixes (2)
Related Models
© 2024 MakerWorld