Barista Express Hopper lid

Remixed by

Barista Express Hopper lid

Remixed by
Boost
12
45
25

Print Profile(1)

All
X1 Carbon
P1S
P1P
X1
X1E
A1

0.28mm layer, 3 walls, 10% infill
0.28mm layer, 3 walls, 10% infill
Designer
1.4 h
1 plate
4.7(11)

Open in Bambu Studio
Boost
12
45
25
17
89
68
Released

Description

Content has been automatically translated.
Show original

A lid for the Breville Barista Express hopper, should you choose not to use it and prefer a closed top to your machine.

 

For a funnel alternative, consider the model Sage Hopper Funnel by @kylekennedykk.

Comment & Rating (25)

Please fill in your opinion
(0/5000)

Print Profile
0.28mm layer, 3 walls, 10% infill
my best day to day use print so far. easy to use, locking bolts perfect fit. Just a brilliant design that every breville/sage user should get and use. get a proper grinder and you are all set. thank you for uploading this for free
The designer has replied
1
Reply
Glad someone else had a use case for this.
1
Reply
Replying to @omBratteng :
it's great. If I had one suggestion it might be to close off the hole to the grinder or make it some sort of mesh filter insert. maybe someone move it around and knocks something inside it or move it so one of the two clips falls out. the chance personally I think is like 1%, but it's technically possible :)
0
Reply
Replying to @Bekkenes :
Good suggestions, I'll see what I can do :) Could maybe add some magnets in the lid too, so it's more stable.
1
Reply
Boosted
This is excellent, thank you! - would the creator be able to make some sort of cone-like internal funnel to allow the beans to not get stuck in the holes?
(Edited)
The designer has replied
1
Reply
Thanks! Take a look at this one that someone else suggested, it's an add-in you just insert https://makerworld.com/en/models/443310 Edit: added link to it in main description as well.
(Edited)
1
Reply
Boosted
Replying to @omBratteng :
That is fantastic - thank you kindly and again for making the original design!
1
Reply
Boosted
Print Profile
0.28mm layer, 3 walls, 10% infill
Great model, great work on making the base fit into the locking mechanism of the hopper! Would be 5/5 if the lid would snap or screw into the base so it sits more secure.
1
Reply
Print Profile
0.28mm layer, 3 walls, 10% infill
The lid works great with the Sage Hopper Funnel for Barista Express/Pro https://makerworld.com/en/models/443310 for single dose grinding
1
Reply
Print Profile
0.28mm layer, 3 walls, 10% infill
looks amazing ! printed it to make the machine looks better as i weigh the beans every time
1
Reply
The cupboards in my kitchen are so low which results in me pulling my machine out toward me every time I want to make a coffee. This has helped but I noticed that some of the beans can get caught and dont make it to the grinders. So I made a little funnel that sits inside to help get the beans to the grinder. You can find my addon here https://makerworld.com/en/models/443310#profileId-349408 Thank for your design, it got me most of the way to where I wanted to be after years of putting up with the issue I had!
1
Reply
Printed this for my friend unfortunately one of the locking pins is getting pushed out and the grinder will not grind without it pressed in.
The designer has replied
0
Reply
Noticed this happens a occasionally for me too, but I don't use the grinder. You could try to scale the pins up a bit to see if it makes the fit tighter so it doesn't slide out.
1
Reply
Replying to @omBratteng :
modified the pins to be longer made several lengths, so you don't have to push them in to press the sensor, also made few that have the pin cut under angle so they can slide in easier. Will se if that fixes it :D If that wont work will try to oversize them little bit overall for tighter fit
1
Reply
Replying to @user_761071206 :
How did it go? Do they fit better now=
0
Reply
Exactly what i was looking for
1
Reply
Print Profile
0.28mm layer, 3 walls, 10% infill
printed with zero issues
1
Reply
Print Profile
0.28mm layer, 3 walls, 10% infill
1
Reply