Godzilla 2024 by MiX&BitS

MiX&BitS

Toys & Games>Characters

Print Profile(8)

All

X1 Carbon

P1S

P1P

X1E

A1 mini

single color split in 2 pieces spikes and body 0.2mm layer

Designer

8.6 h

2 plates

4.9(106)

3 colours colour split (tongue and eyes coloured) 0.2mm lay

Designer

9.7 h

2 plates

4.9(30)

13 cm tall single colour 0.2mm layer, 2 walls, 15% infill

Designer

7.1 h

1 plate

5.0(21)

13 cm tall 2 colours 0.2mm layer, 2 walls, 15% infill

Designer

24 h

1 plate

4.8(18)

Click to see more

Boost

1128

1692

372

104

4.7 k

1.8 k

Released

Description

***

Hi guys,

for more characters from the Monsterverse come and join our Patreon membership www.patreon.com/Mixnbits

Update Kong ready to dowload!

King Kong 13 cm tall by MiX&BitS - MakerWorld

*Update: Check the third print profile named single colour split in 2 pieces.

I'll upload soon also the fourth profile “3 colours colour split (tongue and eyes coloured)”.

Hello people!!

Here comes something different from the previous cute prints!

A sculpture based on the new Godzilla vs Kong movie 2024.

It's a fanart inspired by the new trailer.

I hope you like it.

I will post both the print profile in 1 color and a print profile version in 2 colors… Just the basic shades.

More shades might be added to teeth and gums but being a small statue might be too much purge for smal details.

Enjoy!

Comment & Rating (372)

@gmerelas

UPDATED and UPLOADED 3° profile and 4° profile for the 3 colours. it is still 13 cm tall. I suggest don't downscale it too much if you want the claws and spikes to be printed properly and supports removing not damaging them.

(Edited)

GIF

The designer has replied

@smashd

Boosted

Awesome, thanks very much! Will print later! Spikes will be new roll of PLA Glow Blue, still not sure about the main body ... something fancy like burnt titanium maybe detracts from the Glow, I don't know yet ... 😅 Also: you've posted 6 minutes ago, perfect timing I guess haha

@gmerelas

Replying to @smashd :

eheh. Yes, I didn't have any glow pla so I printed the spikes in silk platinum, just to see if the pieces fit well together. We will paint it later. The connectors are a tiny bit loose (just a bit) just in case some filaments expand a little bit. Might be good for resin also.

@smashd

Boosted

Replying to @gmerelas :

I don't mind loose fit, it's impossible to accomodate for the slack some printers might have or how the chosen filament behaves with the settings used... I'll happily slap some glue on rather than sanding it down for half an hour. 😅 Edit: btw, printing right now, spikes already done. 🥳

(Edited)

@eugenesaur

Boosted

Hi! Great work! Could it be printed as 2 different objects separately? For example, body with some pla, and the back with some translucent PETG, or PLA Glow? And then glue them together by some guideline after, or assemble with some kind of connectors? Just to avoid a lot of purge.

The designer has replied

@EVERYTHINGPLUSU

I agree please upload 2 part. 3mf so we can print in color separately

@gmerelas

Hey thanks for reaching out. I'll look into that today! 👍

@smashd

Boosted

Replying to @gmerelas :

thanks 👍🏻 ready to fire up my new roll of PLA Glow as well (for the back only) 😄

@printcells

Boosted

Print Profile

13 cm tall single colour 0.2mm layer, 2 walls, 15% infill

Fantastic model ! Only needed slight improvements in printing :)

The designer has replied

@gmerelas

Thanks. :-) I am uploading updated version soon :-) Also cut in two pieces.

(Edited)

@printcells

Boosted

Replying to @gmerelas :

Two piece model will be an absolute banger <3

(Edited)

@Cwgbsg1

Replying to @gmerelas :

I just want to know does it have any joints

@printerama

Boosted

Print Profile

single color split in 2 pieces spikes and body 0.2mm layer

Scaled it up to 20cm and printed at 0.16 layer height. Godzilla X Kong... Can't wait!

The designer has replied

@gmerelas

Amazing spikes color!

(Edited)

@printerama

Boosted

Replying to @gmerelas :

Eryone dual color.

(Edited)

@nomadprime

Hi, what color did you use for those spikes?

@ItzAle_Jandro

great print! I might redo this one again with the Fine 0.12mm settings on bambu studios. The head lost some detail on the standard profile setting of 0.2mm; a smaller layer height might help with out a bit. Otherwise, it was so much fun to print! I made it as a surprise for my buddy with Glow in the Dark Filament, as he is a big Godzilla fan. Did not disappoint!

The designer has replied

@gmerelas

Amazing print! Yes definitely smaller layers would make wonders on this model :-)

@ItzAle_Jandro

Replying to @gmerelas :

Most definitely! I am super new and learning how to change settings for prints, toy around and see how it changes things. So no joke, the day I made this comment was the day I learned about layer heights (haha, I know, I am a noob). Still, it is exciting to learn, and this was one of the more intricate prints I have done. So thank you for all the spillover knowledge that came along with your print. I appreciate you. I read your forum regarding your prints. Best of luck to you guys <3

@gmerelas

Replying to @ItzAle_Jandro :

Thank you so much!! I didn't know you could still reply to a model comment when private. Good! If you don't have the Vault Boy and want to get it is free do download in our Patreon Page (browsing in the page it should be post n.10 or something like that). We hope Makerworld will change something in this new and flawed system so We come back public again. In the meanwhile we are considering Thangs 3d...