⬡ Hex Lamp for LED Strip Lights by TripleGWorkshop

TripleGWorkshop

Household>Decor

GIF

Print Profile(2)

All

X1 Carbon

P1S

P1P

X1E

Designers Suggested 0.2mm layer, 2 walls, 15% infill

Designer

8.6 h

1 plate

4.8(25)

0.2mm layer, 2 walls inside, 1 wall outside, 15% infill

7.5 h

1 plate

4.5(2)

Boost

330

480

392

158

Released

Description

I developed this to hold most of a 5m strip of LEDs, cut off or tuck in the remainder.

LEDs HERE https://us.store.bambulab.com/collections/led-strip-light?skr=yes

Super easy instructions:

Poke the wire through the bottom hole.

Remove backer and tightly stick the LED strip up the inner tube.

Put the parts together and plug in, so simple!

The remote receiver is outside the lamp and works perfectly!

Comment & Rating (44)

@JasonMakes

Boosted

Printed cover in white, transparent, and frosted transparent to see which I liked better. I still can't decide. Great model!

The designer has replied

@TripleGWorkshop

wow!

@user_4134630153

Printed using translucent PETG with supports. Highly recommend using PETG for the higher glass transition temperature and natural transparency of PETG. White works well, but the clear one with the slow “clear” BL profile works best with this model. Total print time was almost 3 days

(Edited)

The designer has replied

@TripleGWorkshop

wow!

@user_4134630153

Replying to @TripleGWorkshop :

I recommend using BTFlighting off Aliexpress "WS2812BEco white 60 led/m" strips as that one is low power and one injection point provides enough power without any major voltage drop on that strip. They are half the price of Bambu Labs version. I also recommend this controller "GLEDOPTO ESP32 WLED" off Aliexpress that uses WLED and has more features than the BL one. Power brick I recommend a 5V 6A with a DC barrel that plugs into the WLED ESP32 box. Here is the final build with transparent PETG, which I highly recommend for this project for maximum clarity.

@BabyYoda

Boosted

Printed it in Tiffany Blue and it’s stunning

The designer has replied

@TripleGWorkshop

@bearlissimo

Print Profile

Designers Suggested 0.2mm layer, 2 walls, 15% infill

straightforward print with nice results, thank you

The designer has replied

@TripleGWorkshop

That's fire :)

@ryan5508

Print Profile

Designers Suggested 0.2mm layer, 2 walls, 15% infill

Turned out great. Looks fantastic when lit up

@Carbo

Print Profile

Designers Suggested 0.2mm layer, 2 walls, 15% infill

great Lamp, but i have to spend some time in optimizing my Filament and printer.

@christian.boehl

Great Design and Perfect for WLED :-)

@mikeyriot171

Print Profile

Designers Suggested 0.2mm layer, 2 walls, 15% infill

Great lamp design, came.out really good!

@HijskraanOpa

Print Profile

Designers Suggested 0.2mm layer, 2 walls, 15% infill

(Edited)

@Fotogy

Hey there! I was wondering what PSU you used to drive those LED's? I got some slight experience with those LED-Strips and i know that you need a beefy PSU to use them to their full extend.

The designer has replied

@TripleGWorkshop

I used a bad 1w charger and it got dimmer towards the end so I would recommend something bigger. On computer USB and a decent phone charger block it seemed ok.

@Fotogy

Replying to @TripleGWorkshop :

oh damn! thanks! might buy that strip then!