Shelf Support Bracket
Remixed by
Boost
57
98
52
Print Profile(5)
Shelf Bracket 105mm PLA - 0.2mm layer, 5 walls, 25% infill
Designer
52 min
1 plate
Shelf Bracket 125mm PLA - 0.2mm layer, 5 walls, 25% infill
Designer
1.1 h
1 plate
Shelf Bracket 175mm PLA - 0.2mm layer, 6 walls, 25% infill
Designer
1.4 h
1 plate
Shelf Bracket 150mm PLA - 0.2mm layer, 5 walls, 25% infill
Designer
1.3 h
1 plate
Click to see more
Boost
57
98
52
1
265
343
Released
Description
Remixed from andrethomas' bracket. Rounded the back corner and adjusted the holes to fit coarse drywall screws. Includes 105, 125, 150 and 175mm versions.
While profiles for PLA and PETG as provided, I prefer PETG for the added strength and to avoid material creep. Also note that these have not been tested to hold any particular amount of weight, so use some judgement on how these are printed and how much weight you subject them to.
Comment & Rating (52)
All
Print Profile
Shelf Bracket 125mm PLA - 0.2mm layer, 5 walls, 25% infill
Excelente, muy resistente :)
The designer has replied
1
Reply
¡Gracias!
0
Reply
Print Profile
Shelf Bracket 175mm PETG - 0.2mm layer, 6 walls, 25% infill
Clean and smooth! thank you!
The designer has replied
1
Reply
Very nice! Thank you for sharing and the great rating!
0
Reply
Print Profile
Shelf Bracket 125mm PLA - 0.2mm layer, 5 walls, 25% infill
perfect!
1
Reply
Print Profile
Shelf Bracket 175mm PLA - 0.2mm layer, 6 walls, 25% infill
So far so good. Used PETG.
0
Reply
Print Profile
Shelf Bracket 175mm PLA - 0.2mm layer, 6 walls, 25% infill
works good when printing just one at a time lol the worst that happened when I pushed it too far on an A1 by choosing two on one plate was this little blemish easy to clean but it's 100 percent my fault for trying to print two and it going over the edge almost lol my plate needed scraping. anyway it still worked after canceling the bad one by hitting skip. so I still got a working bracket so it's a great design to have survived my irresponsible attempt at saving time
0
Reply
Print Profile
Shelf Bracket 105mm PLA - 0.2mm layer, 5 walls, 25% infill
great
The designer has replied
0
Reply
Print Profile
Shelf Bracket 175mm PLA - 0.2mm layer, 6 walls, 25% infill
the file barrier my nozzle and was the only print from the app so far that has done this
The designer has replied
0
Reply
Sorry to hear you had an issue. Were you using a textured plate? This profile uses the standard Bambu P1S, textured plate and filament settings so I'm not sure it's related to a setting I can control. I just did another test print and it came out just fine.
0
Reply
Print Profile
Shelf Bracket 125mm PLA - 0.2mm layer, 5 walls, 25% infill
These came out way stronger then I expected, print good in Petg.
The designer has replied
0
Reply
Thanks! I'm glad they worked out for you. I have two 6ft shelves for trophies and toys in a kids room, and they have survived so far ;)
0
Reply
Print Profile
Shelf Bracket 105mm PETG - 0.2mm layer, 5 walls, 25% infill
perfekt, merci!
1
Reply
Print Profile
Shelf Bracket 125mm ASA X 0.16mm layer, No Support in Holes
Printed 8 so far in 2 different PLA. Great results. Well thought out design!
0
Reply
Related Models
© 2024 MakerWorld