ProClip Filament Clip


Print Profile(26)

ProClip V2 Low Profile 6-Pack (Official)
ProClip V2 Low Profile 6-Pack (Official)
Designer
X1 Carbon, P1S, P1P, X1, X1E, A148 min
4.9
ProClip V2 Low Profile 12-Pack (Official)
ProClip V2 Low Profile 12-Pack (Official)
Designer
X1 Carbon, P1S, P1P, X1, X1E, A11.5 h
4.8
ProClip V2 6-Pack (Official)
ProClip V2 6-Pack (Official)
Designer
X1 Carbon, P1S, P1P, X1, X1E, A145 min
4.8
ProClip V2 Low Profile (Official)
ProClip V2 Low Profile (Official)
Designer
X1 Carbon, P1S, P1P, X1, X1E, A119 min
4.9
Click to see more

2141
3745
2792
12.3 k
14.4 k
Released
Copyright Claim
Model
Comment & Rating
Remixes
Related Models

Description

Meet the ProClip!

The ProClip Filament Clip is a pleasure to use and easy to print.

 

ProClip has a built-in handle that works in coordination with a clamping tunnel to manage and secure your filament.

NEW! ProClip V2 features:

  • A extra durable clamp inside the tunnel.
  • Symmetrical input holes work for right handed and left handed users.
  • Handle flange provides good control and a comfortable grip.
  • A Low Profile option designed for tight storage containers.

 

 

 

BENEFITS:

  • Built-In Self Adjusting Clamp
  • No Supports
  • No Overhangs
  • No Brims
  • Designed for FDM Printing
  • Free to Download!

UPDATES:

  • 10/06/23 ProClip V2 Released

 

TIPS:

  • MUST be printed on side
  • Printer tolerances vary. If your ProClip is running tight just slide a piece of filament back and forth to break it in a little bit.
  • Glue stick can help condition the print bed for proper adhesion/release and is recommended.

 

NOTES:

  • ProClip can be used commercially, but can’t be resold.

 

TESTED PRINT DETAILS:

ProClip has been built around the following conditions.

  • Glue Stick: Yes (without is at your own risk)
  • Support: Disabled
  • Walls: 2
  • Brims: No
  • Nozzle: 0.4mm
  • Layer Height: 0.2mm
  • Infill: 15% Gyriod

License

This work is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Comment & Rating (2792)

Please fill in your opinion
0/5000

Print Profile
ProClip V2 6-Pack (Official)
After a small test print, I decided to print a "few more" ;)
The designer has replied
6
Reply
Excellent! 😍
(Edited)
0
Reply
Works great! added labels since I sort my spools by filament color. thanks for sharing.
(Edited)
The designer has replied
4
Reply
Sweet setup! Thats one big happy family of ProClips, thanks for posting!
2
Reply
Print Profile
ProClip V2 (Official)
parfait rie. a redire
The designer has replied
1
Reply
Beautiful! Thanks for sharing your photos - enjoy!
(Edited)
1
Reply
By the way, love that filament - what is it?
0
Reply
Replying to @JDJDJD :
oui il est sympa vous le trouver sur le cite arianeplast en lien https://www.arianeplast.com (PLA + gris aluminium métalliser good filament french ...et aussi sur amazo......ya du choix normalement
(Edited)
1
Reply
Print Profile
ProClip V2 6-Pack (Official)
Nice clip. I was using a simple open design previously but over time the clips relaxed and stopped working. I don't think this one will.
(Edited)
The designer has replied
1
Reply
Sweet pic! What filament is the ProClip printed in? Thanks for your post!
0
Reply
Replying to @JDJDJD :
That's Bambu PLA-CF. I figured the carbon fibre would help with grippiness and it works great.
0
Reply
But you have used the part incorrectly - the open end comes through the hole.
0
Reply
The print profile is no longer public
When printing in ABS on textured PEI I find that small prints with low surface area contacting the build plate will have a high likely chance of failure if they do not include a brim, as seen here. If you're planning to print this on anything other than PLA, unless your confident in your build plate adhesion I would recommend printing w/ a brim. EDIT: I totally didn't see that the OP specifically said glue stick should be used in the description. Updating the rating as I'll chalk up my failure to user error. But I've uploaded some print profiles with brims for anyone that has issues.
(Edited)
The designer has replied
1
Reply
Replying to @JDJDJD :
I have no doubts that with glue it would have adhered just fine, but i use my PEI specifically to avoid having to use gluesticks in the first place. This PEI plate works perfectly without any adhesives, but I've found that specifically with ABS/ASA if the part is very small with low surface area contact there is a high chance that it will come off the plate without a brim. I decided to print these in ABS so i wouldn't need to worry about removing them when drying my spools. I'm sure if these were printed in PLA I also wouldn't have had an issue. Edit: I've updated my rating and added a bit more to the comment to add additional context. Thanks for reaching out, i really like your clip design!
(Edited)
2
Reply
Replying to @myth.ethical.0c :
Cool cool - glad you got it sorted out. To be fair (and to not annihilate the print profile rating lol) the tips did/do say to use glue stick which it will print perfectly with. Anyways I’m glad you like it and happy you got it setup how you want it. 👌 Thanks and enjoy!
(Edited)
1
Reply
Replying to @JDJDJD :
I did just see that 😓 I'll adjust my rating since I totally glossed over that in the description lol
0
Reply
Print Profile
ProClip V2 6-Pack (Official)
prints nice!
The designer has replied
1
Reply
Great print and cool filament! What filament is that?
0
Reply
Replying to @JDJDJD :
its pla basic grey from bambu
(Edited)
1
Reply
Print Profile
ProClip V2 12-Pack (Official)
Print worked great had to make a couple to get size right. Then I printed off 12 pcs and thay are awesome thank you for you model cheers.
(Edited)
The designer has replied
0
Reply
You’re welcome! I’m glad you think they’re awesome - please rate accordingly.
0
Reply
Replying to @JDJDJD :
sorry it wasn’t a successful print because I ran out of filament. I was still able to use them so it will not let me give you file stars as I just tried again. I still love you makes thank you.
(Edited)
0
Reply
Replying to @berniemcglone :
No worries, thanks for the effort - enjoy!
0
Reply
Print Profile
ProClip V2 (Official)
impression rapide et marche parfaitement
The designer has replied
1
Reply
That looks 🔥! Thank you for sharing and for the 5 stars! By the way, what filament is that?
(Edited)
1
Reply
Replying to @JDJDJD :
This dual color filament red&gold by eryone. It works well with the ams
0
Reply
The print profile is no longer public
printed the 6 pack off and they came out great, will definitely use them in the future when I have more spools sitting around.
The designer has replied
2
Reply
Nice! Thanks for the 5 star rating and your pic!
0
Reply
Excellent. I used the non-low pro version and printed them in white so I can quickly mark the filament type (a little less professional than @Melbo0 but it'll work for me).
The designer has replied
1
Reply
Fantastic - Enjoy! @HammerTime
(Edited)
0
Reply

Remixes (0)

There are no remixes yet