Samsung Galaxy Watch 5/6 - Ladestation / charger base Remixed by Printforme

Remixed by

Printforme

Tools>Organizers

Print Profile(2)

All

X1 Carbon

P1S

P1P

X1E

V2.1 With support, and larger hole of the charging station.

Designer

2.9 h

1 plate

4.5(22)

(LEGACY) V1.0 Bambu Standard 0.20mm / without preparation

Designer

2.6 h

1 plate

4.5(8)

Open in Bambu Studio

Boost

229

200

Released

Description

DE:

UPDATE V2.1:
-Mit vorgefertigter Stützstruktur (3mf).
-Loch für die Ladestation wurde ein wenig vergrößert.

Eine edle Ladestation für deine Samsung Galaxy Watch.

Passend für:
-Galaxy Watch5 40mm und 44mm
-Galaxy Watch5 (Classic) 45mm
-Galaxy Watch6 40mm und 44mm
-Galaxy Watch6 (Pro) 43mm und 47mm

Aussparung wurde von mir passend für die neuen Ladestationen der Watch Uhren abgeändert.
Der Standfuß hat zudem zwei Aussparungen für 2 Magnete (10x2mm) bekommen.

PS:
-NICHT passend für das D-Buckle Band!
-V1.0 ist veraltet.

Vielen dank an den ersteller @skaua3d
https://www.thingiverse.com/thing:5595725

_______________________________________________________________________________________________________________

EN:

UPDATE V2.1:
-With prefabricated support structure (3mf).
-Hole for the charging station has been enlarged a little.

An elegant charging station for your Samsung Galaxy Watch.

Suitable for:
-Galaxy Watch5 40mm and 44mm
-Galaxy Watch5 (Classic) 45mm
-Galaxy Watch6 40mm and 44mm
-Galaxy Watch6 (Pro) 43mm and 47mm

I modified the cutout to fit the new charging stations for the Watch watches.
The base also has two recesses for 2 magnets (10x2mm).

PS:
-NOT suitable for the D-Buckle band!
-V1.0 is deprecated.

Many thanks to the creator @skaua3d
https://www.thingiverse.com/thing:5595725

Comment & Rating (41)

@user_2132384120

great print.

@markobil

Print Profile

(LEGACY) V1.0 Bambu Standard 0.20mm / without preparation

Die Ladestation an sich mega schön. nur leider nicht für 5 Pro! musste jetzt vestimmt 6x anpassen und Drucken. Wäre Toll wenn es ein Update geben würde für die 5Pro. musste ein Loch machen damit das Armband komplett drauf passt, sowie hinten abschneiden. Das Loch oben für die Ladebuchse, ist viel zu eng, musste rundum fast 0,05mm abschleifen, dass es rein passte.

The designer has replied

@Audifreak117

Sorry das du Probleme mit dem Halter hast. Allerdings passte meine alte Watch 5 Pro sehr gut. (Das auf dem Bild ist ein Watch5Pro) Ich geh ganz stark davon aus das dies leider an dem teuren D-Buckle Armband liegt :D. Da scheinbar weder der Orginal Ersteller noch ich dieses Armband besitze, ist eine anpassung leider nicht möglich. Ich werde es in der Beschreibung zusätzlich vermerken, danke dafür. Du könntest natürlich deine anpassung sehr gerne als Remix hier oder auf Printables hochladen. Wäre dir sehr dankbar dafür. Mit der Ladebuchse gebe ich dir zu 100% recht. Diese ist in meiner ersten Version (LEGACY) leider viel zu eng geworden. In der neuen V2.1 wurde das Loch deutlich vergrößert. Danke für die trotzdem sehr positiv ausfallende Bewertung und Make obwohl du probleme hattest.

(Edited)

@BottaioRetroTec

Print Profile

V2.1 With support, and larger hole of the charging station.

The model is essence a very nice and clean charger base for the Galaxy Watch 6 charging puck. It truly is at it's full potential when using matt black if i may honestly say so. Even though the profile was made for ABS, i modified it to accept PLA as a material. Since that's the only matt black filament i currently had in stock. Now as for printing, which is done with an X1C, the print came out mostly clean. Minimal cleanup necessary, which was quite nice, so i'll rate it 5 out of 5 stars.

The designer has replied

@Audifreak117

Thanks for the good review on both platforms :D

(Edited)

@Subroda

Doesn't fit the galaxy watch charger the hole is far to small which is a real shame given the really nice design.

The designer has replied

@Audifreak117

Sorry that it doesn't seem to suit you. It's true that the old version was very narrow. But as you can see in the picture, the charging station still fit. However, due to many reports, I revised the model again and enlarged the hole.

@Subroda

Replying to @Audifreak117 :

greatly appreciated I'll re print and test

@MFDesigns3D

Print Profile

V2.1 With support, and larger hole of the charging station.

great print

@woflxrx

Print Profile

V2.1 With support, and larger hole of the charging station.

Bigger than I anticipated, but a great charging stand nonetheless!

@Dexebal

Print Profile

V2.1 With support, and larger hole of the charging station.

really cool. I like it

@MouseWur

Print Profile

V2.1 With support, and larger hole of the charging station.

The designer has replied

@Audifreak117

Hey, can you maybe share where you're having problems with the new version? Or do you just not like the model? lg

@MouseWur

Replying to @Audifreak117 :

failed print, maybe the slice settings I'm not sure.

@Audifreak117

Replying to @MouseWur :

I tested the profile again with ABS and had no problems. I'll try PETG again tomorrow. Other people's reviews also suggest that this problem is not due to the printer profile. Please check your filament again to see if it has absorbed moisture.

GIF

@anthonyrecchia9

Print Profile

(LEGACY) V1.0 Bambu Standard 0.20mm / without preparation

part came out looking good and fit together great but charger did not fit in without extensive cleanup being sliced with the handy app. caused some loose layers on the overhang of the charger

The designer has replied

@Audifreak117

I'm sorry to hear that. Unfortunately it was my mistake. It's too late now, but I have released a new version with pre-mounted supports and a slightly larger hole for the charging station.