Magsafe iPhone and Apple Watch Stand, angled 30° Remixed by J3n50m4t

Remixed by

J3n50m4t

Household>Office

Print Profile(1)

All

P1S

P1P

X1 Carbon

X1E

0.08mm layer, 2 walls, 15% infill

Designer

3.5 h

1 plate

4.2(43)

Boost

147

278

232

Released

Description

Doesn't work with iPhone in Vertical Mode.

Remixed as I wanted to directly see my Watch in Standby-Mode. I removed triangles around the Magsafe and closed a gap at the Watch Charging Port.

Note by the author jpbruce

- The gap on the front of the Watch Charging port is only there to be able to fit the USB-C plug on the newer cables through the hole, as it is longer than the watch charging puck itself (It's not necessary if you have the older USB-A charging cable) - The cutouts around the MagSafe Puck are for the camera bump of the phones. Your phone will probably not sit flush on the charger without them, leading to worse charging efficiency.

Comment & Rating (52)

@treecewx

Print Profile

0.08mm layer, 2 walls, 15% infill

works perfect with my iPhone 14 Pro Max and Apple Watch Ultra. Only downside is MagSafe puck is loose added some 2 sided tape behind it and good to go.

@lmp1982

Print Profile

0.08mm layer, 2 walls, 15% infill

(Edited)

@aliatar

Print Profile

0.08mm layer, 2 walls, 15% infill

@jpbruce

Thanks for your remix! Just two quick remarks to consider: - The gap on the front of the Watch Charging port is only there to be able to fit the USB-C plug on the newer cables through the hole, as it is longer than the watch charging puck itself (It's not necessary if you have the older USB-A charging cable) - The cutouts around the MagSafe Puck are for the camera bump of the phones. Your phone will probably not sit flush on the charger without them, leading to worse charging efficiency.

The designer has replied

@J3n50m4t

Hi, thanks for the Basedesign! 1st: Didn't knew - will add the Info. 2nd: I'm using a 13 Mini with a MagSafe Case - charging efficiency is worse anyway. With the Case the camera is even on my phone. Without the bigger cameras in mind I just didn't know why there were cutouts. The design is good for me - if you don't mind I would cite you in the description, so nobody will print it for the trashbin?

@jpbruce

Replying to @J3n50m4t :

sure, sounds great! Yeah in your case I guess you don't need the cutouts.

@bheine91

Leider nicht für die Orignal Teile von Apple geeignet. Die passen nicht rein. Schade und schön Zeitverlust für sowas zu drucken... Ich habe ein Watch Series 8 (kleinere version) und Iphone 13 Pro Max. Also vom Watch series USB C Stecker passt nicht rein (leider zu eng).

(Edited)

The designer has replied

@J3n50m4t

Tut mir leid, steht in der bewchreibung. Ich hab ein usb a Watch Kabel meiner alten Uhr und es dafür angepasst. Der usb c der neuen Uhr ist länger und passt deshalb nicht. Ich werde das aber mal eher in die Beschreibung stellen damit nicht noch mehr Leute Müll produzieren.

@lorinan

Print Profile

0.08mm layer, 2 walls, 15% infill

File prints perfectly, but my Apple Watch charger (official that came with the watch) is too large for the watch portion by about 1 mm diameter, and the magsafe phone charger portion is too small by around 3 mm diameter. That said, if someone has parts that fit, it's a great design.

The designer has replied

@J3n50m4t

This seems pretty weird to me. My Charges (Apple Watch Series 4, SE ad Ultra 2) are all the same and fit. Did you print on a Bambu? It's a perfect fit on my p1s (as visible on the pictures). I may could provide one with other diameters if you can measure what you exactly need.

@m.drozd.88

Same problem, nail drill from my wife saved the situation. To use it, you must remove the cover, which is terribly irritating. It would be nice if there was a support to hold the phone so you wouldn't have to remove the cover.

@GonnaMakeWeirdS

Print Profile

0.08mm layer, 2 walls, 15% infill

awesome print! only suggestion is the new watch charger is the same hole size as the phone and is usb-c, little bit of carving and I got it through 👍🏼

@Raab3Dprints

Print Profile

0.08mm layer, 2 walls, 15% infill

Looks good, no need for support. Maybe put some nuts or someting heavy into the model, so it doesnt lift up from the kabels.

@ZenithPilot

The watch charger MUST be a USB-C variant. Apple Watch chargers that are USB-C can not be installed. You may also need some double-sided tape to help secure the mag-safe chargers.