LED Sleeper Mount (Beta) - P1S by K-Studio.ca

K-Studio.ca

3D Printer>3D Printer Accessories

Print Profile(3)

All

P1S

P1P

X1 Carbon

X1E

Beta 1.01

Designer

6.5 h

3 plates

5.0(3)

Beta 1.0 to 1.01

Designer

4.4 h

1 plate

Beta 1.0

Designer

2.8 h

2 plates

4.5(4)

Boost

Released

Description

LED Sleeper Mount for P1S, please leave comments and feedbacks for this beta model; I don't know how well it will fit X1C / P1P.

Retain the same printer height profile, no riser.
This is a sleeper mount, hidden LED inside the chassis.
Anti-Glare shield / limit light leakage out at the top.
Total 4 pieces frame.
3 pegs clip to hold the frame together.
Support LED strip up to 14 mm in width.
Corner bend perfectly for LED strip.
Left side and right side frame has two screws hole each.
- Left side frame two screws are the left panel screws. Middle hole one is lower.
- Right side frame two screw are the right panel screws. Middle hole one is higher.

Release History

March 25, 2023
STEP files are available.

March 16, 2023 - Beta 1.01
Optional upgrade if you find the front piece is too flimsy.

March 11, 2023 - Beta 1.0
Initial release.

Instruction for Beta 1.0

For Beta 1.01, it will only have two pegs.

Left frame uses the lower screw hole as shown here.

Comment & Rating (18)

@br1acc

Boosted

Print Profile

Beta 1.01

Printed in ABS at 100.20% scale. Good design and I can't complain about the print, but it is a little finicky to install. If you ever need to remove the LED mount...good luck with the adhesive. I soldered silicone wires near the middle of my LED strip, and added a JST connector to plug directly to the P1S so I can control with with the front display/Bambu Handy. Definitely is too bright. I'm not the best with electronics - I'm not sure if I can just add some kind of resistor to make it dimmer.

@Filippo80

Print Profile

Beta 1.01

1 di 3 per illuminazione interna

@Cobobricks

Print Profile

Beta 1.0

I am suprised there isn’t more riserless designs. This used way less filament then most risers, and I didn’t have to rework my existing ventilation solution! assembly was pretty easy, albeit a little finicky, but the end result is good. printed in Bambu PETG with tree supports for the big front piece. My LED light are maybe a bit too bright for my liking, but that’s not a fault of the design.

(Edited)

@luckyluc.64

Excellent design job; I print it in ABS with no issue. I turn 90 degrees the piece that needs support to minimize the support and use tree support. Oh, and I also changed the infill for gyro; it's much stronger. I use the 4-piece model. That can't be installed on an X1C (Sadely). There is a cover on the right side, and the left side is in the way of the chain link... No good.

The designer has replied

@AeonJoey

I want to cry. lol. I’ve been looking for a good way to mount led strip inside the X1C since I got it, I refuse to use a riser!

@luckyluc.64

Replying to @AeonJoey :

That's why I downloaded it. I would like it to work. Like you, I don't want a riser. I like your joint system with the taper pin. The sad thing is inside the X1C, on the left side, there is a cap covering a PCB and a bunch of cables. Plus, there's a bump totally in the way in the middle. I did look for any place to put something and it's like not possible. If you like to have pictures, I can get you some.

@kstudioca

Replying to @luckyluc.64 :

I uploaded the step files (RAW files), feel free to remix for X1.

(Edited)

@br1acc

Boosted

@kstudioca Do you have any issues with the LED strip adhesive? I print a lot of ABS and I think the chamber temps might be weakening the adhesive. ALTHOUGH it only seems to be falling off in the right side - I wonder if the PTFE tube rubbing against the LED could be the cause.

The designer has replied

@kstudioca

Mine hasn't fallen off, really depends on the LED adhesive they used, you can maybe add a bit of superglue at the end of the strip.

@br1acc

Boosted

Replying to @kstudioca :

Cool, I might just end up making some kind of clip to hold it in multiple places.

@kstudioca

Replying to @br1acc :

STEP files are in the RAW download box, feel free to use them.

@simognodi

How and where should the LED strip be connected?

The designer has replied

@kstudioca

There is a USB port behind the front panel, if you have an LED with long USB cable should work.

@luckyluc.64

Print Profile

Beta 1.0

Sadly, it won't work on my X1C. If I can find time and the machine is not busy, I'll try to see if I can make it work. I like the jointing system. Thanks for sharing

@n.weinrich

Print Profile

Beta 1.0

works very good!

@TKDNinja

Print Profile

Beta 1.01

Came out perfect, no more gunk on the floor!

@user_1983755164

printed the long part with no issue using PETG, the shorter lengths took several attempts but I got there in the end. the holes don’t align with the P1P frame but I understand they may have old and new versions. mine is the newer frame. Design was spot on though.