Samsung Galaxy S24 Case v1.1 - Schutz Huelle Remixed by Toni_ThesBer

Remixed by

Toni_ThesBer

Tools>Gadgets

Print Profile(1)

All

X1 Carbon

P1S

P1P

X1E

0.2mm layer, 5 walls, 20% infill

Designer

1.7 h

1 plate

5.0(2)

Boost

Released

Description

This is my first Samsung Galaxy S24 case now version 1.1 - a remix from lucas_sp12.
No support is required in the slicer settings :-)
The green parts in the picture are the supports for easy printing and must be removed after. Removing can be easy or difficult depending on material and printer.

New version v1.1 changes:
The entire housing is 0.2 mm thicker and therefore more stable. Volume button cutout adjusted slightly. The microphone holes are a little larger so that it fits better. The Support is a little thinner so it can be removed more easily.

Additional version +33% thicker v1.1:
I also designed a more robust version with a 33% thicker wall all around.

See also version 2 with AI text --> https://makerworld.com/en/models/229311

and new version 3 Voronoi --> https://makerworld.com/en/models/432695

Happy Printing
Toni

----------------------------------------------------------------------------------------------------------------

Dies ist meine erste Samsung Galaxy S24 Hülle jetzt Version 1.1 - ein Remix von lucas_sp12.
In den Slicer Einstellungen ist keine Unterstützung erforderlich :-)
Die grünen Teile im Bild dienen lediglich als Stützen zum einfachen Drucken und müssen anschließend entfernt werden. Das Entfernen kann je nach Material und Drucker einfach oder schwierig sein.

Neue Version v1.1 Änderungen:
Das gesamte Gehäuse ist 0,2 mm dicker und dadurch stabiler. Der Ausschnitt der Lautstärketaste wurde leicht angepasst. Die Mikrofonlöcher sind etwas größer, damit es besser passt. Der Support ist etwas dünner, sodass er leichter entfernt werden kann.

Zusätzliche Version +33% dicker v1.1:
Ich habe zusätzlich eine robustere Version mit eine um 33% rundum dickere Wand entworfen.

Schau auch Version 2 mit KI-Text --> https://makerworld.com/en/models/229311

und neue Version 3 Voronoi --> https://makerworld.com/en/models/432695

Viel Spaß beim Drucken
Toni

Category: Mobile Phone

Comment & Rating (12)

@Fluffybutterfly

can I print this in pla?

The designer has replied

@Fluffybutterfly

or petg?

@Toni_ThesBer

Hello, it is better to print it in TPU (flexible filament). You can print it in PLA or PETG, but dropping it on the floor wouldn't protect the phone as well. When choosing between PLA and PETG, PETG is always better. Best regards Toni

(Edited)

@Fluffybutterfly

Replying to @Toni_ThesBer :

thanks

@ImNotNut

Print Profile

0.2mm layer, 5 walls, 20% infill

Printed very well in PLA Basic. Printed for the wrong phone though so I couldn't test the fitment. This is for the S24 not the S24+, which I should have noticed.

The designer has replied

@Toni_ThesBer

Unfortunately I can't help because I don't have a S24 plus

@ImNotNut

Replying to @Toni_ThesBer :

Not a problem, that was my bad lol. Design was awesome, and came out great.

@Domeke

Boosted

printed in plain PLA. works but you need to cut off the top edges because the PLA is too stiff for them, the phone won't fit in. With the edges cut off, you can wedge the phone in and it won't fall out. nice print, thank you!

The designer has replied

@Toni_ThesBer

Thank you to. :-)