Baby Garfield 4 colours
Copyright Claim
Baby Garfield 4 colours
Boost
1086
1413
159
Print Profile(8)
0.2mm layer, 3 walls, 10% infill
Designer
15.4 h
1 plate
0.2mm layer, 3 walls, 10% infill
Designer
2 h
1 plate
KEYCHAIN 1 colour 0.2mm layer, 3 walls, 10% infill
Designer
42 min
1 plate
Tiny 4 colour Keychain 0.2mm layer, 3 walls, 10% infill
Designer
8 h
1 plate
Click to see more
Boost
1086
1413
159
18
3.4 k
686
Released
Description
He is very cute! I sculpted it yesterday and it went directly to print test!
You can print it in 4 colours (5 or 6 takes a little bit too much time but would be more accurate with light brown eyes and dark yellow muzzle-the part under the nose, but 4 colors will do) or in 1 and colour it yourself.
Please, be carful with the whiskers and the support removal. I put a tree light support but you can switch to normal tree if you prefer.
P.S. If you want to give him a friend, you find Odie here Baby Odie 4 colours by MiX&BitS - MakerWorld
I hope you like it!
Enjoy!
Comment & Rating (159)
All
I couldn't pass up making 3 at one time as well and throwing a benchy in for the purge. All of them came out great.
The designer has replied
6
Reply
Great idea!!! I also love the Garfield benchy. Thanks!!!
1
Reply
Printed 4 of them and finished the print on an A1 mini after about 23 hours. I like the glossy look. Thanks for sharing the model!
The designer has replied
2
Reply
Very nice print! thanks for sharing!
0
Reply
Very nice!! I am glad you like the model :-)
0
Reply
15 hours plus to print. The poop chute clogged a couple of times. Looks like at one point it threw the layout off. lots of poop for sure.
The designer has replied
0
Reply
Yes, lot of poop for sure! Sorry for the clog! Did happen to me with anothr model when I used the 0.2 nozzle with wood filament. I found out that it is better using 0.4 with that kind of filament. Can it be the same with marble filament (or the one you used for the eyes) ?
0
Reply
No, I was using a .04 nozzle. I think it’s the film that that causes the clog in the poop shoot.
0
Reply
Replying to @user_668474025
The film? You mean the file? Mmm I doubt that as no one else had reported that problem. Yes, now that I remember I was using 0.4 too with the wood filament when I had the clog. this kind of filament can cause it
0
Reply
Print Profile
Single color, 50% size
smile
1
Reply
what build plate do you have?
0
Reply
Thanks!
0
Reply
Print Profile
0.2mm layer, 3 walls, 10% infill
Came out great. Had trouble removing some of the supports and lost a whisker. I cut a small piece of black filament and made a new one. E6000 to glue it on. Be aware that, due to the color changes from orange to black and the infill using the next filament color, the body has a bit of a black cast to it for about 1/3 of it. Still looks great
The designer has replied
0
Reply
That's correct. Very important to check the flush volumes. I had a similar problem right now with a print. Flush volumes in the first one about 550 in the second 660. See the lines! :(
0
Reply
Replying to @gmerelas
Thanks. I contemplated to increase the wall volumes to 5 to make it more opaque but haven't tried that yet. 12.5 hour print.
0
Reply
Printed Great on my P1S.
Just a quick tip, if you heat up the supports for a sec you can remove the supports without breaking anything
The designer has replied
1
Reply
that's very useful!! thank you very much!
0
Reply
Thank you for this beautiful garfield
The designer has replied
1
Reply
My pleasure! Thanks for rinting our model !
0
Reply
Print Profile
0.2mm layer, 3 walls, 10% infill
whiskers are pretty useless, otherwise great
The designer has replied
1
Reply
Hi There, Thanks for the feedback.
Why don't you give a try to the model I just uploaded? It's a smaller version for Keychain. There's the 4 colour version and you just need to erase the torus and scale it up to the size you like and you have a no whiskers (whiskers are painted on the model) version.
Keychain Baby Garfield with painted on whiskers by MiX&BitS - MakerWorld
(Edited)
0
Reply
Print Profile
0.2mm layer, 3 walls, 10% infill
der Druck sieht toll aus
Es war mein erster 15std Druck
The designer has replied
1
Reply
Und ich muss sagen, dass es ein ziemlich schwieriger Druck ist. Guter Junge!
I hope I translated it correctly! :-)
(Edited)1
Reply
Boosted
Print Profile
0.2mm layer, 3 walls, 10% infill
thank you! printed puurrfect!
(Edited)
The designer has replied
0
Reply
Perfect print!
0
Reply
License
This user content is licensed under a
Creative Commons Attribution-Noncommercial-NoDerivativesRelated Models
© 2024 MakerWorld