Halo 2 SMG with silencer by brentglover1970

brentglover1970

Props & Cosplays>Replica Weapon

Print Profile(1)

All

X1 Carbon

P1S

P1P

X1E

0.2mm layer, 2 walls, 15% infill

Designer

10.8 h

2 plates

4.4(8)

Open in Bambu Studio

Boost

167

278

340

174

Released

Description

Halo 2 Anniversary SMG with silencer game model designed for “Misriah Armoury” Fallout 4 nexus mod

Split and remodelled to allow parts to fit together easier.

I placed multi parts on a couple of plates, but split them down and printed more individually personally.

Glueing is required parts are fitted like this:

note the laser pointer (green under silencer) has a small part to glue onto it that butts up to the main part
the magazine (beige part on top of image) goes onto the side - I mounted it too far forwxard in the photos - you can mount it further towards the stock

End product rendered:

Based on excellent work:

"Halo 2 anniversary - SMG" by McCarthy3D is licensed under Creative Commons Attribution.

halo

smg

master chief

Comment & Rating (19)

@user_3813391170

Print Profile

0.2mm layer, 2 walls, 15% infill

pretty good, I wish the locating holes were better, you have to just eye ball how straight things like the stock and body get glued together

@a_salami

This model should be scaled 125% for a more realistic size/feel. Also, some issues with the model: 1. there is a large gap between the trigger assembly and the upper. This seems to be caused by a sloped area at the bottom-front of the upper where the front of the trigger assembly should slide in to join with the upper. 2. There's no way to mechanically attach the stock to the upper. You're going to have to glue it. I don't know why the model doesn't use a tongue and groove on both ends instead of just for the stock. 3. the top of the laser assembly is flat. It should be rounded to match the diameter of the suppressor. it will need to be glued. 4. There is no mechanical way to attach the foregrip. It must be glued. 5. There's no easy way to attach the magazine. A shallow indentation in the upper would have at least helped with this. It will need to be glued. 6. The suppressor isn't rounded; it's round-ish with 26 faces. 7. The grippy bumps on the handgrip fell off for me. I'll probably just end up stippling the grip with a soldering iron to make up for it.

(Edited)

The designer has replied

@brentglover1970

"Glueing is required parts are fitted like this:" I know it needs glueing, I am still slowly learning more and more in Fusion and will be tackling joints, tongue/grooves and fittings one day:)

@leon411

Print Profile

0.2mm layer, 2 walls, 15% infill

Other Issues

The designer has replied

@brentglover1970

Did you have a problem on this to rate it 3 stars? Anything I can help with?

@wollip

Replying to @brentglover1970 :

He may have faced the same problem I sometimes get.After finishing the print Bambu Studio fails to sync with Makerworld automatically.I will have to do it manual again.If I dont it will be in the Rate List shown as incomplete and only a up to 3 Star Rating is possible.I personal dont rate at all in this case instead to decrease the average rating.

@brentglover1970

Replying to @wollip :

@wollip Yeah I know thats the strange thing with ratings - I get it on both sides though - people want their points so they go rating crazy at the beginning of the month and how can you rate something 5 stars if it never finishes or if you get the dreaded sync error? I do what you do though - if I didn't finish one, I tend not to rate as unless there was a physical problem with the file it's probably on me or my build plate :)

@ManCave3D

whats the little pin for? it was part of the print, from the picture below it looks like its for the part under the suppressor but there's not holes there?

The designer has replied

@brentglover1970

The little pin goes on the side of the laser unit under the silencer and goes into a small pin hole on the body under the silencer