Easter bunny by SabreDesign

SabreDesign

Household>Festivities

IP Report

Print Profile(30)

All

X1 Carbon

P1S

P1P

X1E

A1 mini

H2D

0.16mm layer

Designer

1.4 h

1 plate

4.9(2.1 k)

0.2mm layer

Designer

1.1 h

1 plate

4.9(750)

Strong Ears 0.2mm layer, 1 wall, 0% infill

1.2 h

1 plate

4.9(209)

150% with Strong Ears 0.2mm layer, 1 walls, 0% infill

2.3 h

1 plate

4.9(234)

Click to see more

Open in Bambu Studio

Boost

5108

10713

4282

2.9 k

31.3 k

29.6 k

Released

Description

Modern easter bunny decoration. The model is 110 mm tall, can be scaled up to your liking.
The inside of the model is hollow to save on filament.

If you want to support me or get commercial licenses you can join a patreon membership: https://www.patreon.com/SabreDesign
For one time support you can also buy me a coffe here: https://buymeacoffee.com/sabredesign

Boost Me (for free)

Check out more of my designs below and on my profile:

Comment & Rating (4282)

@Mrsooks57

nice decoration I added a bell inside to be able to play with my rabbit

The designer has replied

@SabreDesign

great idea!

@HardwareMaster

Did you put a pause in the gcode did it manually? :)

@110011

Boosted

Replying to @HardwareMaster :

normaly thats the way to do it.

@SusiKnalltuete

Print Profile

0.16mm layer

Klasse Modell, prima Druck!!!

@switek16v

Klasse! Welches Filament hast du genommen?

@SusiKnalltuete

Replying to @switek16v :

Bambu PLA silk silber

@Mr_Peter

What is the diameter of the hole? Thank you

@3DPrintsBF

Print Profile

0.16mm layer

great design, my wife ordered several in different sizes and colors 👍🏻 so WAF upgraded 🤣thanks for sharing

@pet5631

I have got an order from my gf as well, and she likes your colors a lot. Can you maybe tell me what filaments you used in this picture?

@3DPrintsBF

Replying to @pet5631 :

the beige is Bambu matt pla, front grey is stone grey geeetech matt pla the green I actually don’t recall unfortunately

@Bandito2113

hey! know I’m a little late lol but just so you know you can run a lighter quickly through the spaces to eliminate the stringing!

@radek.rypar

Print Profile

0.2mm layer

@SabreDesign

awesome colour!

@radek.rypar

Replying to @SabreDesign :

Rosa3D - MagicSilk Frozen

@RCALEXRO

Boosted

Print Profile

0.16mm layer

I do appreciate the design. I printed it 15cm tall, with 0.8 extra fine setting. after it go finished, aroud the base of the ears, i did see some defects... but did not give attenton. my daughter grabbed it by the ears, and of course, it broke off. i will try to reprint with different settings. I still appreciate the designers work!

@Diaprint3D

Boosted

Same problem, how are you fixed?

@RCALEXRO

Boosted

Replying to @Diaprint3D :

glue... :)

@FoxCube

Replying to @Diaprint3D :

If you want to fix design, add modifier in slicer, and put it only on ears (add infill for ears) and it should work. I did that and it fixed this issue without adding lot of material for whole design.

@kenissa

Great design! I really like its style and simplicity! But I’ve printed this now, different settings, different filaments and different sizes, and all of them seem to have these 2 artifacts on the head; like 2 layers at the bottom and top of the head, that creates a line, and some stringing. the entire print looks great, except those 2 lines. not sure why. and I can see that other pictures in here has the same.

The designer has replied

@SabreDesign

What scale is this one? The lines normally come from the infill, when you set the infill to 0% tend to disappear

@kenissa

Replying to @SabreDesign :

I have scaled this one up to 150mm in height. There's 1 wall and 0% infill. Here's another one, original height, Bambu Lab PLA Matte filament and also 1 wall and 0% infill. The entire bunny looks good, except ~8mm on each side of the narrowest part of the neck, and again ~8mm below the top of the head. Normally, I would think that this was an issue with the printer or filament, but the artifacts are so consistent across the different sizes and filaments. it's the exact same places that this artifact occurs.

(Edited)

@SabreDesign

Replying to @kenissa :

Okay, did you download my profile? Because there is a height modifier in there that will print the ears with 2 walls and infill. If the starting height isnt raised when scaling up the infill will already start earlier, around the neck. So that might be the issue.

(Edited)

@Sonic68

Print Profile

220 % 0.16mm layer, 1 walls, 0% infill

top

@Linfisso

Boosted

thanks🫶

@d.horak93

Print Profile

0.2mm layer

good model.

@EG_007

Print Profile

0.2mm layer

love it! printed really well and feels great.

@Cameron1223

Print Profile

220 % 0.16mm layer, 1 walls, 0% infill

Decorating with these is great

@Linfisso

Boosted

thanks🫶

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Get Commercial License