Silica drying box (硅胶干燥剂烘干盘)
Copyright Claim
Silica drying box (硅胶干燥剂烘干盘)
Boost
107
227
41
Print Profile(2)
0.2mm layer, 2 walls, 45% infill
Designer
53 min
1 plate
0.2mm layer, 2 walls, 45% infill
1.7 h
1 plate
Open in Bambu Studio
Boost
107
227
41
6
414
201
Released
Description
- 烘干过程需加热，请使用PETG材料进行打印
- The drying process requires heating, please use PETG filament for printing.
- 热床温度70度，更高的温度盘子会粘在热床上，大约需要2-3小时可完成干燥
- The temperature of the heat bed is 70°C. Higher temperatures will cause the box to stick to the heat bed. It may takes about 2-3 hours to complete drying
- 可根据自身需要进行大小缩放
- The model can be resized according to your needs
- 切片默认两层墙一层底，其他使用45%网格填充，可根据需要调整切片参数
- 2 walls and 1 bottom layer 0 top layer 45% infill. The process can be adjusted as needed.
Comment & Rating (41)
All
Boosted
我放大了150%在P1S上打印，去掉了底面，让它更像一个筛子，用内六边形填充更利于PETG打印，交叉点不容易堆料，这样空隙更大，但硅胶干燥剂完全不会掉下来，我准备用在干燥箱风干。我加厚了外墙到0.5，让放大后的悬垂更容易打印，也增加了强度。我甚至用了修改器补上了外壁最顶层的缺失，完美
The designer has replied
0
Reply
这个六边形填充的底效果看着真不错，传个打印配置呗？
0
Reply
Boosted
Replying to @user_3898224
只是些微小的改动，你喜欢的话我可以传一个(^w^)
1
Reply
Print Profile
0.2mm layer, 2 walls, 45% infill
perfektes Ergebnis- danke für das tolle Design 🎉
0
Reply
Print Profile
0.2mm layer, 2 walls, 45% infill
Printed in PA6-GF and it's perfect.
0
Reply
Print Profile
0.2mm layer, 2 walls, 45% infill
It works!
0
Reply
Print Profile
0.2mm layer, 2 walls, 45% infill
adhesion to the PEI plate was way to strong (no glue) even after waiting for 8 hours
0
Reply
Print Profile
0.2mm layer, 2 walls, 45% infill
great
0
Reply
Print Profile
0.2mm layer, 2 walls, 45% infill
Prints fast, I like it
0
Reply
之前就想做了，就是没想到很好的镂空方法最后用双头切片改的，学到了
The designer has replied
0
Reply
活用切片软件有时候比建模好使，其实我开始打了个底是全镂空的，实测不行，干燥剂这玩意儿它一烘容易掉渣……掉的满哪都是……
1
Reply
Replying to @user_3898224
我以前拿微波炉热很容易碎，感觉应该是不能温度变化太剧烈，我用热床加热还好，碎的不多
0
Reply
Print Profile
0.2mm layer, 2 walls, 45% infill
I printed two of them in slightly different sizes so they can fit into each other.
Works excellent for drying Silica Gel.
0
Reply
Boosted
非常棒的模型！
0
Reply
License
This user content is licensed under a
Creative Commons Attribution-Share AlikeRelated Models
© 2024 MakerWorld