Honeycomb Dice Tower Kit Card (Bonus Badges Available)
Copyright Claim
Honeycomb Dice Tower Kit Card (Bonus Badges Available)
Boost
157
236
45
GIF
Print Profile(3)
0.2mm layer, 2 walls, 15% infill
Designer
2.7 h
2 plates
Badges Only
Designer
30 min
1 plate
0.2mm layer, 2 walls, 15% infill
3.2 h
3 plates
Open in Bambu Studio
Boost
157
236
45
8
298
280
Released
Description
03/02/2024 update
Designed two decorative badges that can be embeded on honeycomb panel. Uploaded a separate print profile. Feel free to try it.
—
A honeycomb version of Easy-to-Assemble Dice Tower. To fit all components in kit cards, I scaled 0.75, so the overall filament cost is only 56g. This dice tower can still roll 15.8mm dices smoothly.
Comment & Rating (45)
All
Print Profile
0.2mm layer, 2 walls, 15% infill
Very cool and easy to print out. Giving as a gift, can't wait.
1
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
ottimo, poco materiale e bel progetto
1
Reply
Boosted
Print Profile
0.2mm layer, 2 walls, 15% infill
The designer has replied
1
Reply
Thank you for sharing👍
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
1
Reply
Boosted
Print Profile
0.2mm layer, 2 walls, 15% infill
The gaps could be a little tighter for all but the front and back plate. Assembly is a little tricky since they don't hold snug until the front/back plates are in place, and the gate that catches the dice likes to fall off if you roll a heavy metal die. Rolls great for standard resin dice and is a fun talking piece when assembling at the table
(Edited)The designer has replied
0
Reply
Hi Tav3n, thank you for the detailed feedback. I will improve in the next version.
1. tighten the gaps except the front and back plates.
2. enhance the gate to avoid falling off.
Besides, I am curious, do you prefer a bigger dice tower or the current size is enough?
0
Reply
Boosted
Replying to @GammaLand
The current size works well for me because everyone at the table has their own tower or tray. My LED D20 does get stuck inside but it's oversized and very lightweight so I don't trust it's rolls anyway lol. It would be hard to share, but I just tossed an extra kit in the bottom of my DnD box to give away if someone needs a tower
0
Reply
Boosted
Replying to @GammaLand
The current size works well for me because everyone at the table has their own tower or tray. My LED D20 does get stuck inside but it's oversized and very lightweight so I don't trust it's rolls anyway lol. It would be hard to share, but I just tossed an extra kit in the bottom of my DnD box to give away if someone needs a tower
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Printed well but some of my d20's get consistently stuck. Some are fine though. I'd recommend scaling up a tiny bit.
0
Reply
by how much?
0
Reply
Replying to @cesa94izq
I haven't printed another one yet. I would think as little as 3-5% should do the trick.
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Prints great!
The designer has replied
1
Reply
Thank you😁
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
this is going to make a great gift for my dnd group.
The designer has replied
0
Reply
lol, enjoy it😄
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
prints great!
The designer has replied
0
Reply
thank you 😄
0
Reply
License
This user content is licensed under a
Creative Commons Attribution-NoncommercialRelated Models
© 2024 MakerWorld