Tesla Model 3 Vent Iphone 13 Pro Max Phone Holder
Remixed by
Copyright Claim
Tesla Model 3 Vent Iphone 13 Pro Max Phone Holder
Remixed by
Boost
45
96
48
Print Profile(1)
0.2mm layer, 2 walls, 15% infill
Designer
3 h
1 plate
Open in Bambu Studio
Boost
45
96
48
1
167
104
Released
Description
An Iphone 13 Pro Max holder designed for the Tesla Model 3 vents.
I liked the basic idea of the original design but it couldn't hold my phone while i was driving so i found myself never using it so i remixed the model to be a perfect fit for the Iphone 13 Pro Max.
It fits the phone with a case, the slot is 11.5 mm in thickness but after it's printed i think its closer to being 11.3 mm in thickness.
Print settings:
Printer: BambuLab X1C
Layer height: 0.2 mm
Supports: Yes
Rafts: No
Infill: 15%
Comment & Rating (48)
All
Use ASA
The designer has replied
0
Reply
Thank you for sharing your print 😊
0
Reply
好用，稳固没有异响，真是个不错的设计。
The designer has replied
0
Reply
Thank you for your comment :)
0
Reply
Great！！！！！！
1
Reply
Did you print this with PLA? How's it holding up?
The designer has replied
0
Reply
I have printed multiple accessories for the Tesla in PLA and it’s fine never any issues however I am located in Iceland and the cars don’t get very warm here so I would recommend PETG to be safe.
I did have a similar stand there which this is remixed from over winter time where the fans were being full blasted at maximum heat and it held up good with no visible change in the PLA
0
Reply
Replying to @Einstakur3D
I printed in PLA but I do live in Florida ... I'll find out tomorrow if it holds up. Got some PETG ready if it doesn't.
0
Reply
Replying to @Biffiest
So, did it hold up? I'm in FL as well
0
Reply
Printed very well but sadly doesn't fit my iphone 15 pro max. Could you make one with a 12.5mm gap?
The designer has replied
1
Reply
I have the 15 Pro Max now myself and I will try to remake this for the 15 Pro Max when I have time, do you prefer with a case or without a case?
1
Reply
Replying to @Einstakur3D
I mostly run it with case so with case would be awesome
1
Reply
puoi renderlo compatibile per la stampa con A1 mini?
The designer has replied
0
Reply
It's no possible to make it A1 Mini compatible without splitting into 2 parts with connector but if you want it in 2 parts and glue together i can make that print profile for you
0
Reply
Replying to @Einstakur3D
i would glue it!!!
is it possible to make it?
thank you
0
Reply
Replying to @oiojin831
I will look into the best way to split this model for the A1 Mini, I will soon have the A1 Mini aswell which should make it easier to test
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
perfetto e nessun rumore o vibrazione in auto
The designer has replied
1
Reply
Thank you for the rating😊
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
would be better if it fit the contour of the dash. it works for me because I don’t use a case. I use it every day. thanks for the design. 👍🏻
The designer has replied
1
Reply
Thank you for the rating, I thought about the contour but it’s beyond my CAD experience at the moment, but maybe in the future 😊
0
Reply
Will this fit the model Y?
The designer has replied
0
Reply
I am unfortunately unable to test it for you but they are very similar in interior design so I would expect it to fit, but please note that there are 2 prongs that go into the vents and it should sit flush with the wood panel there should not be much of a gap so that it doesn’t slide
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
15 Pro Max fits in but without case
The designer has replied
0
Reply
Thank you for the rating, I have the 15 Pro Max now aswell, might make a new one that fits 15 Pro Max with a case, look out for it if I make it :)
(Edited)1
Reply
This remix is based on
License
This user content is licensed under a
Creative Commons Attribution-NoncommercialRelated Models
© 2024 MakerWorld