Yellow Bulldozer with Movements Version 2

Copyright Claim

Yellow Bulldozer with Movements Version 2

Boost
41
99
22
GIF
GIF

Print Profile(1)

All
X1
P1S
P1P
X1 Carbon
X1E
A1

Ready to Print Profile with supports 0.2mm layer, 2 walls, 15% infill
Ready to Print Profile with supports 0.2mm layer, 2 walls, 15% infill
Designer
13.8 h
4 plates
4.5(2)

Open in Bambu Studio
Boost
41
99
22
1
234
162
Released

Description

Summary

 

I am very thankful to Mr Benoît Lussier for his feedbacks which has helped me refine the model further.

 

Upgrades From Version 1

1) The body panels with grey colors can be now printed seperately and then joined with main body thus the distinct color combination can be achieved without painting.

2) The back panel engine cover is now operated with a hinge mechanism, earlier it was take off type. There is also a lever to hold the tilt position of panel.

3) Interference issues have been rectified.

4) Changes to wheels.

5) Better labelling for screw holes.

6) I recommend to print a engine model and place it inside the engine room so that it is visible when the engine cover latch is opened.

There are three ways to print this.

As single piece:- Please download STL file but there wont be any movements.

As nine pieces :- THE PREFERRED WAY. Please download 3mf file having “combined.3mf” in the name. You can use the same 3mf file as manual for assembling. You may need screws and or glue to complete assembly. There are pin to be printed for movements which can be sustituted with nuts or bots. Lock pins have also be not provided. I have been using a small piece of filament itself as lock pins. Also you may have to scale up the model to get the full play but make sure you dont lose the wall thickness and tolerance.

Full Dismantled :- Download 3mf file with Full_dismantled.3mf. Interference issues are expected as this is the pre processed file. Advise only expert makers to use this. Print at your own risk.

Both the Back Wheels have been made hollow to ensure efficient printing. Makers have the option to either go for hollow wheels for all the sides or go with the solid ones(both front wheels) or a combination of both.

Supports should be provided as required.
Appreciate the makes uploads. Open for suggestions.
 

 

Comment & Rating (22)

Please fill in your opinion
(0/5000)

The control panel model it hard to print even with tree support, I had failed twice and on third attempt. It might be an idea to separate wheel and body. BTW, what support you applied on model or no support?
(Edited)
The designer has replied
0
Reply
Hi there. I can certainly look into that. Is it the combined model that you are having issue with? Can you share any images?
0
Reply
I failed 2 times on body with tree support, and I guess you never print it yourself now. The 3rd print is ongoing but it is doomed to be a failed one, because a body with so many support inside is a nightmare for post-processing , also a waste of filament & time Check this picture of printing, it’s full filled with support inside I do doubt if this model is ready for 3D print or just a 3D model for somewhere else. You should print your upload first
(Edited)
0
Reply
Replying to @adison.wu :
Hi there, sorry for the late reply. I was not getting notifications for replies to comments.I hope this answers your questions regarding print.
(Edited)
0
Reply
Exelent!
1
Reply
The print profile is no longer public
Struggling to get a good print from this profile. Get bad results using supports too
The designer has replied
1
Reply
Which plate are you having issue with? I maybe able to help
0
Reply
Totally understood
0
Reply
is a nice model
The designer has replied
0
Reply
Thanks bro.
0
Reply
Print Profile
Ready to Print Profile with supports 0.2mm layer, 2 walls, 15% infill
1
Reply
Print Profile
Ready to Print Profile with supports 0.2mm layer, 2 walls, 15% infill
1
Reply
No more