Apple Vision Pro Stand

Copyright Claim

Apple Vision Pro Stand

Boost
339
405
106

Print Profile(4)

All
P1P
P1S
X1
X1 Carbon
X1E
A1

0.2mm layer, 4 walls, 15% infill
0.2mm layer, 4 walls, 15% infill
Designer
5.9 h
1 plate
5.0(15)

V2.1 - Smooth Base, Clean supports, Reduced cleanup
V2.1 - Smooth Base, Clean supports, Reduced cleanup
4 h
1 plate
5.0(12)

No supports 0.2mm layer, 4 walls, 15% infill
No supports 0.2mm layer, 4 walls, 15% infill
5.7 h
1 plate
5.0(1)

V2.1 (Ironed Version) Minimal Supports
V2.1 (Ironed Version) Minimal Supports
4.6 h
1 plate
5.0(1)

Boost
339
405
106
22
1.3 k
664
Released

Description

This is a stand for the Apple Vision Pro I made out of a desire to have a compact, vertical stand for my desk and being unable to find one available that did that. You can either print the included rod, or use a dowel of your own choosing that is 0.75" and 215 mm in length (using something fun like walnut, brass, copper, or steel can add a cool look!). It uses four 6 mm rubber feet on the bottom.

 

This is for my 23W light seal model, I'm admittedly not sure how other sizes work with this. Might need to scale the pringle up/down.

 

I printed mine on a Bambu P1S with white marble PLA filament (also from Bambu). I recommend binding all the pieces together with superglue.

 

This is a stand I made for fun in Fusion 360. If you print this and something bad happens I do not take responsibility. You are free to distribute/sell this physically if you would like, but please do not distribute the software files on any other site.

Comment & Rating (106)

Please fill in your opinion
(0/5000)

Print Profile
0.2mm layer, 4 walls, 15% infill
Prints beautifully, I also printed the dowel from PLA Carbon and it’s very sturdy. nice simple, elegant design.
The designer has replied
2
Reply
Wowww. I love that! What is the reddish filament?
0
Reply
Replying to @christianselig :
Bambu Labs red PLA-CF
(Edited)
1
Reply
can you direct me to the dowel print? im new to 3d printing
0
Reply
i tried making it in copper filament but the filament ran out =/ edges very jaggedy, any suggestions?
The designer has replied
1
Reply
0.12 height on a P1S, 4 wall loops, tree supports. will try to reset it to designer default.
0
Reply
Weird, did you print with that part down? It's pretty flat up there so it should be pretty trivial for a printer to print. I would make sure the part with the dowel hole is the side on the bed (and use supports for the bottom), then try printing at an even finer resolution for the top half (you can use variable layer height to make the bottom half 0.2 mm, and the top half 0.08 mm for instance). I would think that would resolve it nicely. Also I don't know much about copper filament, if it's a fancy filament with actual copper in it that might just be a trickier material to print, it was pretty straightforward with Bambu's marble PLA for me. Also I'd recommend placing the Vision Pro on the stand the opposite way, the nose cut out on the stand is intended to form to the nose part of the Vision Pro and it sits at a bit of a weird angle if you use it the other direction
0
Reply
Replying to @christianselig :
Hey Christian! Thank you so much for this model. Printing it right now, and will be printing the dowel after. What settings do you suggest for the dowel? Unsure if it should be generic settings or the same as the Pringle/ base :)
0
Reply
Printed on X1C with Bambu Filament White and Silver.
The designer has replied
0
Reply
Love this, what material did you go with for the rod? That looks awesome
0
Reply
Where the heck do you find a metal rod like that?
0
Reply
Replying to @user_300493544 :
it’s silver PLA as he specified
0
Reply
Print Profile
V2.1 - Smooth Base, Clean supports, Reduced cleanup
not bad.. not bad at all!
The designer has replied
2
Reply
Thanks!
(Edited)
0
Reply
I’m finding the weight of the headset causes the top piece it rests on to tilt forward and detach from the rod. Any tips?! Love the design tho :)
The designer has replied
1
Reply
I would try super gluing it if you haven't already!
0
Reply
I used a bit of wood glue
0
Reply
Print Profile
V2.1 (Ironed Version) Minimal Supports
fitting well and setting safely
The designer has replied
1
Reply
thanks for the rating!
0
Reply
Print Profile
0.2mm layer, 4 walls, 15% infill
This printed very well and looks great!
The designer has replied
1
Reply
Love the multicolors
(Edited)
2
Reply
Very nice. I printed in white and gray PLA to match the AVP aesthetic. Perfect fit.
(Edited)
The designer has replied
0
Reply
That's so smart, I love how that turned out!
0
Reply
Thank you for designing and sharing this. It fits nicely on my "charging shelf".
The designer has replied
0
Reply
Looks great, really nice lighting!
0
Reply
Looks like Vision Pro sold really good. OP what is your impression of Vision Pro?
The designer has replied
1
Reply
I really really love mine, it's such a fundamentally *cool* device, not only to use, but just to stare at haha. I'm having a ton of fun building apps for it
2
Reply
Replying to @christianselig :
Oh so you are a developer. I am a developer too. I work in aviation. Mainly on UAVs (ML models and C) . For fun I build flutter and swift apps. I don’t own AVP yet cause its not sold in my country and bringing is expensive like 4.5-5k which is not worth it. What types of apps do you work on if you don’t mind sharing?
1
Reply
Replying to @berkeozkir :
Apps that are nowhere near as cool/sophisticated as yours :p Right now I build a virtual pets app called Pixel Pals, and an app for watching YouTube on the Vision Pro called Juno.
3
Reply