Apple Vision Pro Stand by christianselig

christianselig

Tools>Organizers

Print Profile(4)

All

P1P

P1S

X1 Carbon

X1E

0.2mm layer, 4 walls, 15% infill

Designer

5.9 h

1 plate

5.0(14)

V2.1 - Smooth Base, Clean supports, Reduced cleanup

4 h

1 plate

5.0(11)

No supports 0.2mm layer, 4 walls, 15% infill

5.7 h

1 plate

5.0(1)

V2.1 (Ironed Version) Minimal Supports

4.6 h

1 plate

5.0(1)

Boost

312

372

1.3 k

630

Released

Description

This is a stand for the Apple Vision Pro I made out of a desire to have a compact, vertical stand for my desk and being unable to find one available that did that. You can either print the included rod, or use a dowel of your own choosing that is 0.75" and 215 mm in length (using something fun like walnut, brass, copper, or steel can add a cool look!). It uses four 6 mm rubber feet on the bottom.

This is for my 23W light seal model, I'm admittedly not sure how other sizes work with this. Might need to scale the pringle up/down.

I printed mine on a Bambu P1S with white marble PLA filament (also from Bambu). I recommend binding all the pieces together with superglue.

This is a stand I made for fun in Fusion 360. If you print this and something bad happens I do not take responsibility. You are free to distribute/sell this physically if you would like, but please do not distribute the software files on any other site.

Comment & Rating (97)

@3DPrints808

i tried making it in copper filament but the filament ran out =/ edges very jaggedy, any suggestions?

The designer has replied

@3DPrints808

0.12 height on a P1S, 4 wall loops, tree supports. will try to reset it to designer default.

@christianselig

Weird, did you print with that part down? It's pretty flat up there so it should be pretty trivial for a printer to print. I would make sure the part with the dowel hole is the side on the bed (and use supports for the bottom), then try printing at an even finer resolution for the top half (you can use variable layer height to make the bottom half 0.2 mm, and the top half 0.08 mm for instance). I would think that would resolve it nicely. Also I don't know much about copper filament, if it's a fancy filament with actual copper in it that might just be a trickier material to print, it was pretty straightforward with Bambu's marble PLA for me. Also I'd recommend placing the Vision Pro on the stand the opposite way, the nose cut out on the stand is intended to form to the nose part of the Vision Pro and it sits at a bit of a weird angle if you use it the other direction

@MikeCam

Replying to @christianselig :

Hey Christian! Thank you so much for this model. Printing it right now, and will be printing the dowel after. What settings do you suggest for the dowel? Unsure if it should be generic settings or the same as the Pringle/ base :)

@aspenweldon

Print Profile

0.2mm layer, 4 walls, 15% infill

Prints beautifully, I also printed the dowel from PLA Carbon and it’s very sturdy. nice simple, elegant design.

The designer has replied

@christianselig

Wowww. I love that! What is the reddish filament?

@aspenweldon

Replying to @christianselig :

Bambu Labs red PLA-CF

(Edited)

@SPMChi

Print Profile

V2.1 - Smooth Base, Clean supports, Reduced cleanup

not bad.. not bad at all!

The designer has replied

@MasterBuilder

Thanks!

(Edited)

@user_2822651893

I’m finding the weight of the headset causes the top piece it rests on to tilt forward and detach from the rod. Any tips?! Love the design tho :)

The designer has replied

@christianselig

I would try super gluing it if you haven't already!

@MasterBuilder

I used a bit of wood glue

@amcdaniel2

Printed on X1C with Bambu Filament White and Silver.

The designer has replied

@christianselig

Love this, what material did you go with for the rod? That looks awesome

@user_300493544

Where the heck do you find a metal rod like that?

@sampazdan

Replying to @user_300493544 :

it’s silver PLA as he specified

@msa1906

Print Profile

V2.1 (Ironed Version) Minimal Supports

fitting well and setting safely

The designer has replied

@MasterBuilder

thanks for the rating!

@Mexigreek

Print Profile

0.2mm layer, 4 walls, 15% infill

This printed very well and looks great!

The designer has replied

@christianselig

Love the multicolors

(Edited)

@spencerdiniz

Very nice. I printed in white and gray PLA to match the AVP aesthetic. Perfect fit.

(Edited)

The designer has replied

@christianselig

That's so smart, I love how that turned out!

@user_767276260

Thank you for designing and sharing this. It fits nicely on my "charging shelf".

The designer has replied

@christianselig

Looks great, really nice lighting!

@berkeozkir

Looks like Vision Pro sold really good. OP what is your impression of Vision Pro?

The designer has replied

@christianselig

I really really love mine, it's such a fundamentally *cool* device, not only to use, but just to stare at haha. I'm having a ton of fun building apps for it

@berkeozkir

Replying to @christianselig :

Oh so you are a developer. I am a developer too. I work in aviation. Mainly on UAVs (ML models and C) . For fun I build flutter and swift apps. I don’t own AVP yet cause its not sold in my country and bringing is expensive like 4.5-5k which is not worth it. What types of apps do you work on if you don’t mind sharing?

@christianselig

Replying to @berkeozkir :

Apps that are nowhere near as cool/sophisticated as yours :p Right now I build a virtual pets app called Pixel Pals, and an app for watching YouTube on the Vision Pro called Juno.