Xbox Series S/X Controller Faceplate by Shaggys3D

Shaggys3D

Hobby & DIY>Electronics

Print Profile(4)

All

X1 Carbon

P1S

P1P

X1E

A1 mini

0.2mm layer, 2 walls, 15% infill

Designer

2.8 h

1 plate

4.8(41)

0.2mm layer, 2 walls, 15% infill

3.3 h

1 plate

4.4(7)

Smooth + Tree Supports (0.12mm layer, 2 walls, 15% infill)

3.7 h

1 plate

4.1(9)

0.2mm layer, 2 walls, 15% infill

2.1 h

1 plate

5.0(2)

Open in Bambu Studio

Boost

284

352

530

331

Released

Description

If you want commercial access please sub to me at

Patreon.com/LightBoxGalore

I will be doing the ps5 and nintendo switch ones as well soon when i can get the controllers in hand.

Not yet satisfied with the back pieces they still need some adjusting but the front is pretty good now that ive been gaming for a couple days with it for testing with no issues.

After printing i rec sanding the holes especially for the joysticks so its smooth and wont damage the joystick.

Comment & Rating (95)

@LateShift

Print Profile

Smooth + Tree Supports (0.12mm layer, 2 walls, 15% infill)

If printing vertical increase hole size on Guide, A and dpad by 0.043 for flush fit. Horizontal worked fine when using Petg as interface for supports. I used variable layer height down to 0,04 up to 0.2. Been using this to finish up last bit of rolls layering it on and making some ugly controller faces.

The designer has replied

@sirfragalot

wait a minute so you rated my profile 4 stars but actually printed your own?

@LateShift

Replying to @sirfragalot :

The model isn't sized properly causing the fit to be wrong on D pad and several other holes and causing a lip to be exposed on both hand holds, your profile has poor support setup making the hole sizing issue worse. I printed it then threw it away because it requires far more work than should be required to make it fit properly; a redesign and dremel. I suggested a better way if people are dead set on using this. Honestly, it's like a 3. I was being nice, but your attitude is a 1.

(Edited)

@sirfragalot

you missed my point. It's not my model, and as you haven't used my profile it's not fair to down rate it for a perceived issue with the model

@sirfragalot

After the 1st one came out (designers profile) I felt it needed more post processing than I would have liked (not knocking the profile, it still came out great). I decided to print again in my favourite filament (OPY Burnt Titanium) and I used my profile. Here is the result: far less post processing, cleaner button holes and much better top edge.

The designer has replied

@Shaggys3D

I got dark magic by cookie cad almost looks like the pics. great print

@Fin3dPrinting

Boosted

Print Profile

Smooth + Tree Supports (0.12mm layer, 2 walls, 15% infill)

very good print profile. a lot smoother!

The designer has replied

@sirfragalot

It's even better when sliced in Orca. It handles support placement loads better

@Fin3dPrinting

Boosted

amazing!! I used designer print profile!

@Pj2leandro

Print Profile

0.2mm layer, 2 walls, 15% infill

printed easy. I had to trip the X box logo hole to make it a tad bigger. I think it was my support that made it that way.

The designer has replied

@Shaggys3D

I rec sanding all holes just to help out no matter what supports used. especially for the analog sticks

@Woogie

Print Profile

0.2mm layer, 2 walls, 15% infill

Using white eSUN PLA+, it looks a little "see-through" in places. I think using 3+ walls would solve this, and doesn't really increase the print time. Thank you very much for the model. I've been looking for a Series S/X controller face plate for ages, and this one is pretty much perfect. Prints well and works great after a little sanding around the thumbstick holes (as you mentioned).

(Edited)

The designer has replied

@Shaggys3D

yea I just threw a quick profile together for it and didn't really go thru settings. basically all stock settings lol. I'm glad ya enjoyed the print!

@Lockett_Tech

Print Profile

Smooth + Tree Supports (0.12mm layer, 2 walls, 15% infill)

this was a cool print. I had to do some sanding to make it fit 100% but I expected that. the screw holes did Crack and needed super glue when installing it on my controller.