Led lamp Rechargeable & Portable

Copyright Claim

Led lamp Rechargeable & Portable

Boost
15
4
0
GIF

Print Profile(1)

All
P1S
P1P
X1
X1 Carbon
X1E
A1

Fullset
Fullset
Designer
10.1 h
2 plates

Boost
15
4
0
2
13
4
Released

Description

The perfect portable lamp for any occasion

 

Looking for a portable lamp that goes anywhere? A lamp that is lightweight and easy to carry? A lamp that provides perfect lighting in any situation?

 

If so, the lampy lamp is the perfect solution for you.

 

This lamp is battery-operated or mains-powered, so it is completely portable. You can take it with you to the beach, the mountains, a camping trip, or anywhere else.

 

In addition, it is very lightweight, so it will not be any effort to carry.

 

The lampy lamp provides perfect lighting in any situation. It has a bright white light that will allow you to see clearly at any time of day.

 

It also has an elegant and modern design that will look perfect in any place.

 

How to assemble?

Before starting to assemble the printed parts we must make the necessary soldering for the assembly of the lamp.

 

If we have opted for the purchased battery holder we must solder following the wiring diagram the + wire to the positive end of the USB-C board and the - wire to the negative end of the USB-C board and the - wire to the negative end of the USB-C board negative end of the USB-C board.

 

If we have chosen to print the battery holder and to solder the cables directly to the battery (Not advisable if you do not have experience) you must solder red cable to the pole + of the battery and to the + end of the USB-C board and black wire to the - pole of the battery and to the negative end of the USB-C board.

 

Once we have this solder, we must solder a cable + and a - of 10cm to their respective poles of the USB-C board.

 

Now it is time for the power button, we must extend the wires (Led +, Led -, NO and C) 20cm. The NO and C wire (in my version red and white wire) must be connected together.

 

Imagen

 

Once the soldering is finished, we move on to the assembly of the lamp.

 

STEP 1

Place the USB-C board in its place with the printed adapter and screw it with 2 M3x8 screws.

 

 

STEP 2

Put the battery holder in place with an M3x8 screw organizing the cables

 

 

STEP 3

Insert the USB-A terminal into the adapter of our LED strip and put it in place.

 

 

STEP 4

Put the wago holder in place with M3x8 screw, and put de wago connectors in their place.

 

 

STEP 5

Place the magnets on the top cover and inside the dome respecting the polarity so that they attract each other.

 

 

STEP 6

Put the power button in place on the top cover and tighten it firmly.

 

 

STEP 7

Insert 1,5 meters of LED strip through the bottom opening leaving the USB adapter at the bottom, start removing the adhesive to glue the LED strip along the round tube leaving a gap of about 0.5cm between each turn.

 

 

STEP 8

Guide the wires from the upper adapter through the center and bring them to the bottom.

 

 

STEP 9

Connect all cables according to the wiring diagram using the wago connectors. Also connect the end of the LED strip to the USB adapter and insert the battery in the holder.

 

 

STEP 10

Place the central part on the base and screw it with 3 M3x8 screws.

 

 

STEP 11

Put the white dome in place by matching the seam at the back and secure it with 3 M3x8 screws.

 

 

STEP 12

Connect the power button with the adapter and put it in place with the magnets.

 


Documentation (2)

Bill of Materials (1)
BOM_430dc20e-9755-4f1a-9172-77ba67c10507.xlsx
Other Files (1)
Diagrama conexion_5d6a0407-a89d-4287-b76c-aba0f7f34bab.pdf

Bill of Materials

Purchase from Bambu Store

Comment & Rating (0)

Please fill in your opinion
(0/5000)

No more