Spiderman Headset Stand / Holder by mateibocancios

mateibocancios

Household>Office

Print Profile(3)

All

P1S

P1P

X1 Carbon

X1E

A1 mini

0.2mm layer, 2 walls, 5% infill

Designer

11.7 h

1 plate

4.9(15)

A1 mini

Designer

5.8 h

1 plate

5.0(3)

Lightning infill

Designer

9.1 h

1 plate

Open in Bambu Studio

Boost

233

279

625

164

Released

Description

Spiderman Headphones holder i made.
Happy printing!

Comment & Rating (29)

@user_4118251715

Print Profile

A1 mini

A little small, but came out perfect. The top was a little bit worse but very good. I really love it. I made it for my brother and he really enjoys it.

The designer has replied

@mateibocancios

It can't be bigger for the A1mini. Thanks for printing.

@user_4118251715

Replying to @mateibocancios :

oh sorry i have p1p but did not have enuph filament so i did that one sorry for the trubel.

@mateibocancios

Replying to @user_4118251715 :

Glad you like it.

@BadManVic

Boosted

Print Profile

0.2mm layer, 2 walls, 5% infill

YUUUUUP!!!! took almost an entire spool. but I don’t give a FRENCH FRY! it came out cool.

(Edited)

The designer has replied

@mateibocancios

Too bad you had that layer shift 🥲

(Edited)

@BadManVic

Boosted

Replying to @mateibocancios :

I was messing with the speeds while it was printing.

@user_911371870

Print Profile

0.2mm layer, 2 walls, 5% infill

Probably my most favorite print yet! I used a silk gold filament and it came out super amazing!

@user_3201487214

Did you print it with or without supports

@JUVN

Print Profile

0.2mm layer, 2 walls, 5% infill

head was a little wide

(Edited)

The designer has replied

@mateibocancios

The print is great. I think it's obvious that you need to scale it for your headphones. i measured it for mine. Giving 3 stars even though you have a perfect print is a bit harsh.

(Edited)

@j.d.alford84

Boosted

Print Profile

0.2mm layer, 2 walls, 5% infill

no issue. printed great

@bodowohlbrecht

Print Profile

0.2mm layer, 2 walls, 5% infill

Super 👍

@user_1947722798

Did you use supports?

The designer has replied

@mateibocancios

Of course, they are enabled in the profile

@mkrbuck

Print Profile

0.2mm layer, 2 walls, 5% infill

The extruder kept popping because as it changed patterns the tip would encounter a piece already built. it was loud probably because the object is hollow and it never broke the object lose of the build plate but it was enough to make me nervous during the entire print. end product is great and would rate it overall a 4.5 of 5.

The designer has replied

@mateibocancios

Hello, thanks for printing! I didn't encounter this problem, but make sure you calibrate you flow for the filament, as this infill is adaptive cubic and overlaps the lines when extruding. I think this is what you heard, the lines overlapping and bumping a little into each other every time they crossed. You might have a little bit of over-extrusion going on, but I am glad it didn't harm your final result. I used adaptive cubic infill to reduce the weight of the infill as much as I could while maintaining strength, but you could maybe try gyroid, as the lines don't overlap the next time you print something similar. Again, happy you like the final result and I would love to see a picture of your print!