v2 GYROID Pattern Reusable Spool (stronger) - Bambu Lab Refill Compatible - Filament Saver

Remixed by

v2 GYROID Pattern Reusable Spool (stronger) - Bambu Lab Refill Compatible - Filament Saver

Remixed by
Boost
169
315
142

Print Profile(4)

All
X1 Carbon
P1S
P1P
X1
X1E
A1

Designers Profile (keep settings as is)
Designers Profile (keep settings as is)
Designer
4.3 h
3 plates
5.0(105)

PETG 0.2mm layer, 2 walls, 15% infill
PETG 0.2mm layer, 2 walls, 15% infill
5 h
3 plates
4.8(19)

ASA - 0.28mm layer, 2 walls, 15% infill
ASA - 0.28mm layer, 2 walls, 15% infill
4.3 h
3 plates
5.0(3)

ABS - 0.28mm layer, 2 walls, 15% infill
ABS - 0.28mm layer, 2 walls, 15% infill
4.4 h
3 plates
5.0(1)

Open in Bambu Studio
Boost
169
315
142
44
634
1.1 k
Released

Description

This model is v2 of this spool. The original works great but some people need a stronger spool, so v2 does the trick without using much more filament!

 

---

 

Calling all gyroid bros who want a stronger reusable spool!

 

 

Gyroid infill is all the rage. It's the strongest and coolest infill style, so why not have it on display while your filament spools rotate?

 

 

Well now you can!

 

 

Introducing my Bambu Lab Reusable Spool (v2) remix with visible gyroid pattern. This fully supports all Bambu Lab refills.

 

 

This remix is based off the official Bambu Lab reusable spool model, so it functions exactly like the official spool, except has the added benefit of a very cool gyroid pattern holding it all together! It also uses less filament.

 

 

Not enough gyroid for you? Well guess what? The infill of the solid parts is also gyroid! An absolute must for all gyroid fanboys (and girls) to show off your obsession.

 

 

Can I change any settings?

I would strongly advise you to NOT change any settings or modifiers in the print profile. I've spent a lot of time getting the right balance of strength and coolness, so each setting is there for a reason. The only settings you can change are filament settings if you want to print in something other than PLA.

 

 

What's the best filament to print this in?

PLA, PLA+, PLA Tough etc. are my favs here. To preserve the strength, it must print well and these print the best without missing a beat. If you dry a lot of filament, print them in PETG or ABS to avoid warping in filament dryers. Do not put this in a filament dryer if you printed using PLA or PLA variants!

 

 

When I attach the spools, I can hear clicking. Should I be worried?

No, this is normal! The RFID tag may gently scrape against the gyroid pattern when closing the spool. Just keep going until it clicks in place.

 

 

Will this block my RFID readability?

Nope! Your AMS will read the tags fine with this reusable spool.

 

 

Do I need to use the spacing shim?

It's been added as a 3rd plate because the official Bambu Lab version uses it. I have never need it personally so I don't bother, but you can use it if you like.

 

 

 

Please let me know what you think and let's see some photos showing off your super cool gyroid pattern spools!

Comment & Rating (142)

Please fill in your opinion
(0/5000)

Print Profile
Designers Profile (keep settings as is)
Great job. More robust than v1 which was already an awesome design
1
Reply
bow so u get the part that says abs and the amount of filament left?
0
Reply
Replying to @Gmoney316 :
It's a sticker in the box of each bambu filament refill
0
Reply
Print Profile
PETG 0.2mm layer, 2 walls, 15% infill
Nice spool for cardboard replacement. Fits nicely in AMS. A bit soft if want to put into vacuum bag.
The designer has replied
0
Reply
The PETG definitely gives them some flex
(Edited)
1
Reply
p.s. works perfectly in combination with the spacer to fill the gap of a narrower cardboard spools (like eSUN ePLA Matte): https://makerworld.com/en/models/19445#profileId-18177
0
Reply
Print Profile
PETG 0.2mm layer, 2 walls, 15% infill
came out perfect! printed in petg
The designer has replied
0
Reply
thanks for the share, the transparent looks great
0
Reply
Print Profile
Designers Profile (keep settings as is)
printed fast and fit well. need to use it immediately for a print so testing it out.
0
Reply
Print Profile
ABS - 0.28mm layer, 2 walls, 15% infill
ABS👌🏻
0
Reply
Print Profile
Designers Profile (keep settings as is)
works great!
0
Reply
Print Profile
Designers Profile (keep settings as is)
fitted perfectly for my ata refill spool
0
Reply
Print Profile
Designers Profile (keep settings as is)
Printed amazing with Transparent Green Sunlu PLA+
0
Reply
Print Profile
PETG 0.2mm layer, 2 walls, 15% infill
I printed this in PETG using supplied settings. Prints with no supports and fits together perfectly. I am a Gyroid fan and realy like how this came out.
0
Reply
Print Profile
PETG 0.2mm layer, 2 walls, 15% infill
Printed with PETG, it can bend and not break. This spool is compatible with R3D refill.
0
Reply