Bambu Lab - Filament Poop Bin - X1, X1C, P1P and P1S Remixed by harrypulvirenti

Remixed by

harrypulvirenti

3D Printer>3D Printer Accessories

Print Profile(9)

All

X1 Carbon

P1S

P1P

X1E

Single Color - Polyterra grey

Designer

7.1 h

1 plate

4.8(625)

Multicolor profile

Designer

12.8 h

1 plate

4.8(448)

Single color 0.2mm layer, 2 walls, 20% infill

5 h

1 plate

4.9(281)

0.28mm layer, 2 walls, 5% infill, 6h37m, PETG

6.6 h

1 plate

4.9(28)

Click to see more

Boost

2190

3906

1716

17 k

7.9 k

Released

Description

It is basically an optimisation of the original design but is functionally the same.
This remix eliminates a rear wall to use less material and makes overhangs less pronounced to make the model easier to be printed.

I strongly recommend using brim to print it if you don't want to see the heel fall.

You can find the suggested orientation used to print the object in the images.

With the proposed orientation the object should fit without scaling it, you will maybe just need to move it a little bit into position, but some user reported that scaling it down to 95% also works well.

I tested it with my X1C and is perfectly compatible.

About the P1P the original model was compatible with the P1P without enclosure and this remix have the same compatibility

Comment & Rating (1716)

@user_3480404137

The print profile is no longer public

This profile is poorly configured and should be deleted.

The designer has replied

@AneoPsy

Sorry for this failure, I printed this profile with my X1C + Bambulab PLA without any problems. It looks like your filament is not dry enough for high speed or maybe the speed is beyond the limit of your filament. If you are using an enclosed printer, did you leave the top or door open during printing?

(Edited)

@user_3480404137

Replying to @AneoPsy :

The issue is that the layer height is at 0.25 and should be 0.24, I'm on the P1S.

(Edited)

@AneoPsy

The layer height is perfect, 0.25 is a great multiple of 0.05 which is the resolution of the stepper motors. I tuned this profile and it was inspired by the bambu lab profile used for their high speed printing. The marks on the walls of your print are due to bad or not dry enough filament that creates bubbles and clog the nozzle. This profile was print at least 3 times with consistent and great results on this model and was print more than 200 times with great result on other models. The only thing that differ is the filament used and the bed used, Bambulab machines still very similar from each other.

(Edited)

@iceyice432

Print Profile

Single color 0.2mm layer, 2 walls, 20% infill

works great for me

@JupiCroco

you turned it into a theme park slide, nice lol

(Edited)

@snakefun

Print Profile

Single color 0.2mm layer, 2 walls, 20% infill

Great, you don't have to do anything, just press print.

@kevfeb

Print Profile

Single color 0.2mm layer, 2 walls, 20% infill

flawless!

The designer has replied

@spary3d

looks very good!

@ben.hallauer

The print profile is no longer public

good overall print and result. union join line on P1s is pretty clear on the support leg. recommend randomizing joint in settings. supports also not needed but recommend at minimum a 3mm brim.

(Edited)

The designer has replied

@AneoPsy

Thanks for reviewing, I appreciate the feedback. What was wrong with your print?

@ben.hallauer

it didn't seem fully on the support foot, however, that could have been potentially a printer problem.

@Killdozer666

The print profile is no longer public

Excellent results. Used 10% infill. Printed in 7 hours. Logo had too much blur due to ringing. But I will re-tune my pressure advance and print again.