The non-photographer's photography box - VERSION 1
Copyright Claim
The non-photographer's photography box - VERSION 1
Boost
84
124
29
Print Profile(1)
0.2mm layer, 2 walls, 15% infill
Designer
9.2 h
1 plate
Boost
84
124
29
0
137
40
Released
Description
Version 2 is out! new and improved without corner lines in the background. Please Check my other models to find version 2!!!
Simple open box that I will use for my makerworld creations.
In the photos, I used an under-cabinet lighting that is for my printer, the mount for it can be found in my other models.
Enjoy!
Comment & Rating (29)
All
well I believe it was a new roll of Sunlu that they had sent me that was the problem. I have had about 60% issues with that Company. I Only use Bambu, NuMakers and Inland usually but if it is free I am not going to turn it down, Right?
I have attached photos of the 2nd attempt with the NuMakers...
The designer has replied
2
Reply
do you dry your filament first?
0
Reply
Yes, I am fanatic about dry filament because I do not like problems, LOL
It was not the filament after all. Discovered what it was by accident on the next multicolor print. The slot three has an issue that is causing under extrusion. Have not had a chance to check the ptfe inside the AMS yet.
Or it could be the feeder gone bad on that slot. Will know more when I have chance to investigate.
Meanwhile I am avoiding that slot(3) and finishing some jobs for now...
Will Post finished photos soon of your booth. Love it!
Already printed your two color led light shell. Amazon is delivering the LED strip you recommended soon...
Thanks My Friend!
(Edited)0
Reply
Replying to @lilrepete
Thanks to your input, I did a new version of print profile and have deleted the original print profile.
To avoid anyone else having any issues, I updated the print profile and removed the fillet from the bottom layer/backside. The bottom layer (on the backside) is now flat with the plate, and should make it easier for the printer to handle. Thank you for your feedback and pictures!
(Edited)0
Reply
What is causing this, I am using your profile?
The designer has replied
0
Reply
what filament is that?
0
Reply
Replying to @kellytrinh
SunLu PLA +
I am trying again on the X1C with Numakers PLA+..
0
Reply
Replying to @lilrepete
is your first layer ok? do you notice any lifting of the edges? sometimes the plate does not heat the edges enough
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Great, works well with additional lighting
The designer has replied
0
Reply
thank you for the rating! really appreciate it!
0
Reply
FYI - I have a new version of this model, I think you will like it more. Check my profile to find the V2 model of this
0
Reply
Replying to @kellytrinh
Much better V2
(Edited)1
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
👍
The designer has replied
0
Reply
thank you! I appreciate the rating!!
0
Reply
FYI - I have a new version of this model, I think you will like it more. Check my profile to find the V2 model of this
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
The designer has replied
0
Reply
thank you! really appreciate the rating!
0
Reply
FYI - I have a new version of this model, I think you will like it more. Check my profile to find the V2 model of this
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
The designer has replied
0
Reply
Thank you! much appreciated!
0
Reply
FYI - I have a new version of this model, I think you will like it more. Check my profile to find the V2 model of this
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
The designer has replied
0
Reply
thank you! really appreciate the rating!
0
Reply
FYI - I have a new version of this model, I think you will like it more. Check my profile to find the V2 model of this
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
The designer has replied
0
Reply
Thank you for the rating! FYI - I have a version 2 of the model that I like much better!
check my model list to find version 2
0
Reply
No more
License
This user content is licensed under a
Creative Commons Attribution-NoncommercialRelated Models
© 2024 MakerWorld