AMS lite fast spool adaptor Geeetech filament spools
Copyright Claim
AMS lite fast spool adaptor Geeetech filament spools
Boost
5
17
15
Print Profile(1)
0.28mm layer, 2 walls, 15% infill
Designer
56 min
1 plate
Open in Bambu Studio
Boost
5
17
15
2
72
73
Released
Description
AMS lite adapter for Geeetech brand filament spools.
Prints in less than 1 hour. less than 30 g of filament.
can be used with filament spools also from other brands whose internal hole is approximately 74 mm.
If you want my complete kit of adapters for ams lite also print my AMS lite cardboard spool adapter (I tested with the 3djake cardboard spool - RPLA).
Printing takes about half an hour. less than 13 g of filament.
Can be used with filament spools also from other brands whose internal hole is approximately 56 mm.
https://makerworld.com/en/models/221623#profileId-239977
my complete kit:
PLACE THE KIT IN THIS POINT. DOES NOT MESS WITH YOUR PRINTS.
Comment & Rating (15)
All
Print Profile
0.28mm layer, 2 walls, 15% infill
Para mí bobina de Geeetech se queda un poquito pequeña de diámetro, pues la bobina gira en el soporte. con 1mm más de diámetro quedaría perfecta. Pondré un poco de cinta adhesiva para ganar ese milímetro y que la bobina no gire.
The designer has replied
0
Reply
Gran solución con cinta adhesiva. El pegamento caliente también podría funcionar. Quizás geeetech cambió el diámetro de las bobinas con el tiempo. desde la cortadora puedes escalar fácilmente el tamaño del objeto para que se ajuste perfectamente. ¡Gracias por la respuesta!
0
Reply
Print Profile
0.28mm layer, 2 walls, 15% infill
Perfecto. Con muy poco material soluciona el problema con las bobinas con el hueco demasiado grande.
0
Reply
Print Profile
0.28mm layer, 2 walls, 15% infill
passt perfekt 👍
0
Reply
So far this has fit my Stronghero3D, 3DdimsFila, and Locyfens filament brand rolls that I have gotten off of Amazon. Thank you, prints fast too.
I don't have an option for stars apparently 5 of 5 stars!
The designer has replied
1
Reply
I assume the dimensions are pretty standard. However, I have indicated the size of the internal hole which should be approximately 74 millimetres. Thanks for the feedback on compatibility with other brands.
0
Reply
Print Profile
0.28mm layer, 2 walls, 15% infill
si stacca dal piatto
The designer has replied
0
Reply
ciao, mi dispiace. Tuttavia non dipende sicuramente dal modello ma dalla pulizia del tuo piatto di stampa.
Ti do qualche suggerimento:
- pulisci il piatto con alcol isopropilico;
- controlla di aver impostato nello slicer il piatto corretto;
- verifica il flusso-temperatura-qualità del filamento che utilizzi;
- non posizionare la stampante vicino a correnti d'aria.
Se dopo quanto scritto sopra non avessi ancora risolto utilizza 2-3 mmm di brim per aumentare l'adesione al piano.
0
Reply
Print Profile
0.28mm layer, 2 walls, 15% infill
Printed super fast and works perfect!
1
Reply
would this same setup work with Prusamint brand?
0
Reply
Print Profile
0.28mm layer, 2 walls, 15% infill
0
Reply
Print Profile
0.28mm layer, 2 walls, 15% infill
0
Reply
Print Profile
0.28mm layer, 2 walls, 15% infill
0
Reply
License
This user content is licensed under a
Creative Commons Attribution-NoncommercialRelated Models
© 2024 MakerWorld