Ikea skadis Singlebox V2
Copyright Claim
Ikea skadis Singlebox V2
Boost
510
1168
137
Print Profile(4)
0.2mm layer, 3 walls, 15% infill
Designer
5.7 h
1 plate
Fast and wider walls, 3mm Brim, 0.6mm width with 0.4mm nozzle, 0.2mm layer, 2 walls, 15% infill
2.2 h
2 plates
0.2mm layer, 3 walls, 15% infill
3.6 h
2 plates
0.2mm layer, 2 walls, 15% infill - For smaller holes
2.5 h
2 plates
Open in Bambu Studio
Boost
510
1168
137
44
1.2 k
817
Released
Description
Back with version 2 of the storage box system for ikea skadis. as you might have seen my first version that was stackable. this version fits side ways, and are stack able. and they come in diffrent sizes. Look for my other designs.
Comment & Rating (137)
All
Die Peg Halter sind nicht richtig erstellt und passen nicht ohne Nacharbeit in die Skadisplatte siehe Bilder. Falls die richtigen Maße gebraucht werden kann ich diese gerne mal zusenden dann passt auch alles wie es soll.
The designer has replied
1
Reply
not sure Why your printer makes Them this Way. but over 500 Other people, including my self, Didnt have this problem 😅
0
Reply
Replying to @JimmiboY
jetzt erzähl mir mal wie dieses Teil an die Skadis Wand passt? ohne Bearbeiten !!!! Die Datei selbst mal überprüfen währe von Vorteil für andere. Wenn ich etwas hier in Makerworld ablege wird es von mir so lange getestet bis es passt.
Schau dir mal das bitte an : https://makerworld.com/en/models/122599#profileId-132102
(Edited)
0
Reply
it would really help if you type in English.. as im not german. but again i Will tell you, i had No issues, mounting it On the plate, i just gently wiggle it in place, like you Can see in the video. i have done No “bearbeiten” to any of my models.
0
Reply
Print Profile
0.2mm layer, 3 walls, 15% infill
difficult to install
1
Reply
passt nicht !!!
(Edited)1
Reply
some of the white and black Skadis is slightly smaller than the other colours. It’s the coating.
you will find this problem with a lot of models if you do have one of the the smaller hole boards.
I swapped mine all for natural wood and didn’t have any more problems.
(Edited)0
Reply
The part of conector is a little bit lager than the hole, it's difficult to install and push down.
2
Reply
ja passt nicht. falsch Konstruiert
0
Reply
Boosted
Print Profile
0.2mm layer, 3 walls, 15% infill
Great storage drawers, my Skadis will soon be FULL OF THESE!
1
Reply
Print Profile
0.2mm layer, 3 walls, 15% infill
Awesome!
1
Reply
Boosted
Print Profile
0.2mm layer, 3 walls, 15% infill
tolerances could be better...but nice design
0
Reply
Boosted
Black filament finished on me and I had to change to gray. Still turned out really well!!
0
Reply
Boosted
Print Profile
0.2mm layer, 3 walls, 15% infill
Top Design and very easy Print 😃
0
Reply
Print Profile
0.2mm layer, 3 walls, 15% infill
Great!
0
Reply
Boosted
Print Profile
Fast and wider walls, 3mm Brim, 0.6mm width with 0.4mm nozzle, 0.2mm layer, 2 walls, 15% infill
Nice Print. supports a wee bit fiddly to clean away but took time all worked out good
0
Reply
License
This user content is licensed under a
Creative Commons Attribution-Noncommercial-NoDerivatives
© 2024 MakerWorld