H.P. Lovecraft bust

Copyright Claim

H.P. Lovecraft bust

Boost
74
148
23

Print Profile(1)

All
X1 Carbon
P1S
P1P
X1
X1E
A1
A1 mini

0.08mm layer, 3 walls, 15% infill
0.08mm layer, 3 walls, 15% infill
Designer
8.6 h
1 plate
4.8(11)

Open in Bambu Studio
Boost
74
148
23
18
121
53
Released

Description

Boost Me (for free)

please consider Boosting me if you like the model and you want to support me so I can make more.
thank you!

H.P. Lovecraft bust

Comment & Rating (23)

Please fill in your opinion
(0/5000)

Print Profile
0.08mm layer, 3 walls, 15% infill
it looks nice from the front, it's pretty bad from the back, but for me it's fine if you can put it somewhere where it won't be seen from the side
(Edited)
The designer has replied
1
Reply
I'd suggest to check your supports settings, you might need to dial them for the filament you are using or your environment, because they seem to be sticking a bit too much to the model
0
Reply
Replying to @FRZ3Dprints :
I printed it too, with green BBL glow filament. I did get some of that "ugliness" on the back, and the settings were those meant for that filament. I think there isn't much we can do, except maybe printing some parts of the model slowly, with the best supports settings we can get... still, gravity is a bitch and there's bound to be some of what we see here. Other than that, removing the supports did work. Once I have reprinted the pedestal (something went wrong and the bottom book didn't get print, don't know why), I'll put up a photo and my rating :) Edit: I found some little problems. Tentacle D isn't fully fused to the pedestal and Tentacle Scylla is missing a bit on its curved section, at the top. Also, what is the angled cut at the bottom of same Tentacle Scylla for? It doesn't seem to match an angle on Howard himself?
(Edited)
1
Reply
Replying to @user_114488885 :
thank you for your contribution! it's this kind of collaboration among people that makes me love the 3D printing world
0
Reply
Worked perfectly with no setting changes on A1. Filament is Bambu PLA Glow
(Edited)
2
Reply
Bust Marble PLA, Stand Silk Gold PLA.
0
Reply
Boosted
I boosted this model because i need more lovecraft models :D
The designer has replied
2
Reply
that's truly too kind of you. I'll be sure to work on them!
0
Reply
Boosted
Print Profile
0.08mm layer, 3 walls, 15% infill
I feel like I wedged him in, in the wrong position, but it still works. Wife loves it!
The designer has replied
1
Reply
you probably made it more of a non euclidean horror! HPL would be proud
0
Reply
Boosted
Print Profile
0.08mm layer, 3 walls, 15% infill
Amazing. I love Lovecraft so I printed this one immediately. I would love big vase mode bust.
(Edited)
The designer has replied
1
Reply
I'm really glad there's another fan of Lovecraft and that you liked the model!
0
Reply
i couldnt get it to print the head no matter what i tried, it would just slide off the print bed
The designer has replied
0
Reply
depending on the type of your plate (smooth PEI, textured PEI, cool plate, off brand, ...), its conditions, the configuration of your filament profiles, it might be a variety of reasons. I'd first clean the plate thoroughly, and if that doesn't help, activate the brim
0
Reply
Print Profile
0.08mm layer, 3 walls, 15% infill
back of the head fell off mid print :(
0
Reply
Thanks
0
Reply
Print Profile
0.08mm layer, 3 walls, 15% infill
1
Reply