Halloween Decorations Door Art 8 Pack by Williams Industries

Williams Industries

Art>2D Art

Print Profile(5)

All

X1 Carbon

P1S

P1P

X1E

0.2mm layer, 3 walls, 100% infill

Designer

1.4 h

1 plate

4.9(19)

0.2mm layer, 3 walls, 15% infill

Designer

11.1 h

8 plates

4.9(17)

0.2mm layer, 2 walls, 15% infill

1.8 h

1 plate

4.9(15)

0.2mm layer, 2 walls, 20% infill (Lighning)+ Ironing

1.8 h

1 plate

5.0(5)

Click to see more

Boost

339

509

101

871

525

Released

Description

These look great on your door frame, I would suggest a little bit of adhesive putty like in the link below. This is a layered print and this is meant to be printed on a Bambu with AMS or Multicolor printer. Makes for great wall art, or you can scale it down and add a magnet on the back for a magnet.

We have a lot of great stuff over at the Patreon: https://www.patreon.com/WilliamsIndustries

Adhesive Putty: https://a.co/d/0SXex0u

Comment & Rating (101)

@nathan.gallop

Print Profile

0.2mm layer, 3 walls, 100% infill

Very cute. Print is easy and hugs the wall nicely. Stays up with no tape or glue. Thought I was getting 8 different plates but was only the ghosts plate. UPDATE: Profiles were reloaded and all 8 plates are being printed now.

(Edited)

The designer has replied

@WilliamsIndustr

looks great! there should be a profile with all plates in there.

@nathan.gallop

Replying to @WilliamsIndustr :

when I go to it through the app. it only shows me 1 plate to choose from. Maybe I’m doing something wrong??

(Edited)

@WilliamsIndustr

Replying to @nathan.gallop :

I can go in and double check, but here is what I see in the app. nonetheless, I will re-upload another one in a bit

@Zoobert

Print Profile

FAST - Pick type of decoration - 0.2mm layer, 3 walls, 15% infill

The cat came out great. The spider one aggressively told me I needed to do some maintenance (clean carbon rods, lubricate lead screws, tighten belts). I'll give that one a shot tomorrow again, now that I've done all that, but I'm sure it'll come out fine.

The designer has replied

@Duncaroo

Happy you like it!

@TashaZ3D

Print Profile

0.2mm layer, 3 walls, 100% infill

printed this in a galaxy black I had and I have to say I’m truly loving it!

The designer has replied

@WilliamsIndustr

perfection!!

@mr.deadius

Some fabulous designs. I love them. Thank you so much!!

The designer has replied

@WilliamsIndustr

Looks awesome!

@NagelD

Print Profile

0.2mm layer, 3 walls, 15% infill

would probably work with less infill too as it's nothing structural. but came out great

@Byandraa

Print Profile

0.2mm layer, 2 walls, 15% infill

Love the Cat, just had to take out the Eyes, did not fit with the other Cats i already have <3 Prints perfectly

@lapayne

Print Profile

0.2mm layer, 2 walls, 15% infill

Great print! I used gold silk PLA for the eyes. the best part of the design is that it looks great flipped either way. I used a textured PEI plate and put it on the right side of the door (showing textured side), but would look just as on the other side, with the smoother side showing. Oh, I did find that the tips of the spiderweb lifted, so I had to use a brim on the outside edge. I use a .16 brim-object gap, which makes the brim pretty easy to remove. Thanks for a great design!

(Edited)

@wplumia.rt

Print Profile

0.2mm layer, 2 walls, 15% infill

Super Design. Beim Drucken anderer Filamentsorten, gesonderte Profile für PLA oder PLA+ erstellen. Auf Temperatur und Geschwindigkeit achten. Many thanks.