MTG Commander deckbox by Dutch3d

Dutch3d

Toys & Games>Board Games

Print Profile(3)

All

P1S

P1P

X1 Carbon

X1E

A1 mini

0.1mm layer, 2 walls, 15% infill

Designer

9 h

1 plate

4.9(18)

FAST (no support) 0.2mm layer, 2 walls, 15% infill

Designer

4.9 h

1 plate

4.5(17)

0.1mm layer, 2 walls, 15% infill

10.6 h

2 plates

4.7(3)

Open in Bambu Studio

Boost

100

172

409

394

Released

Description

A deckbox made for commander decks.

MTG Logo at underside of the lid can be removed if you like.

Comment & Rating (59)

@Torres

Great model 😄👍 just bought my first printer (A1 Mini) and this was my first print, I've printed 3 so far and they all printed perfectly 👌. I used Bambu Lab matte black PLA so the scars from the supports is quite ugly, but other than that they are perfect 😁

The designer has replied

@Dutch3d

Thanks! Enjoy using them Tip: You could try the no support one if you dont have support pla. they might turn out better

@Torres

Replying to @Dutch3d :

Thanks i will try without the supports :)

@nicthalon

Set the support settings back to stock (the round arrows) if printing without pla support, which doesn't come with the mini, or use the no support profile. The mini can do some very impressive bridging.

@user_3338691378

Awesome box!! First PLA basic was good. But on the 2nd try I experimented with Matte + Fuzz (.2 height x .2 spacing, contour) and it came out almost perfect. Excellent quality on P1P. Fuzz on the lid/channels makes it lock in place perfectly. I would just figure how to not make whole interior fuzz for time's sake. Sick mtg box, I love it

The designer has replied

@Dutch3d

Wow that looks cool! If I need anather I wil try the same thing

@user_3338691378

Replying to @Dutch3d :

Maybe try testing with a brim? Both boxes have a slight arch at the bottom, not sure if that's just my bed being wavey or what. That would make it dang near perfect.

@Dutch3d

Replying to @user_3338691378 :

I have no problem with warping, but adding a brim wont hurt ofcourse

@Code_Craft

Print Profile

0.1mm layer, 2 walls, 15% infill

perfect gift!

@KThompson87

such a cool build!

@Getting_Dirty

Print Profile

FAST (no support) 0.2mm layer, 2 walls, 15% infill

Cool and easy to print

@Faeriell

Print Profile

0.1mm layer, 2 walls, 15% infill

Love this magic box :)

@FallenEcclesia

Print Profile

FAST (no support) 0.2mm layer, 2 walls, 15% infill

very good thank you, my lid slides a bit to easily but it’s not a big deal

(Edited)

@getfitgeek

Flip the lid over and the clip will secure in place.

(Edited)

@FallenEcclesia

Replying to @getfitgeek :

I will give this a try thank you

@user_3005240168

Print Profile

0.1mm layer, 2 walls, 15% infill

This box prints very well and looks nice. Its enough room for cards and tokens. I would like to have a rework of the closing because its too lose. Cheers!

@getfitgeek

I thought it was loose also. Turn the lid over. The logo faces down and the little clip secures the lid. You just have to pull up slightly in the middle front of the lid to release.

@user_3811990776

Can you put a top loaded card into the commander slot?

The designer has replied

@Dutch3d

No, the slot is to small for that. only sleeved and double sleeved