Playstation Portal Stand with USB cable slot
Copyright Claim
Playstation Portal Stand with USB cable slot
Boost
61
90
44
Print Profile(2)
0.08mm layer, 2 walls, 10% infill
Designer
7.8 h
1 plate
0.2mm layer, 2 walls, 10% infill
7.5 h
1 plate
Boost
61
90
44
4
265
158
Released
Description
New model of sony playstation portal stand with slot for the USB type C cable.
My first version did the job but this one add the look/design!
No support needed.
Hope you will appreciate it!
Comment & Rating (44)
All
Print Profile
0.2mm layer, 2 walls, 10% infill
The stand printed well, but the sony cable doesn't fit through the slot at all. Printed in Inland PLA
0
Reply
Thank you for your comment. Could you please tell me how many tenth of a millimeter you would add ideally?
I use the original cable, and no problem on my side. Don't know if it is the same cable between US or European version.
0
Reply
Replying to @MaDutt
This area on my cable measures between 6.32mm to 6.41mm, with thicker towards the connector. The other dimension seems to be similar.
(Edited)
1
Reply
to make pretty much any usb-c cable fit easily, I would make the opening at least 13.5mm wide and 8mm tall. But, that is not the only problem with the hole. In fact, your measurements would work for a bunch of cables I have including the one that came with the portal. The issue is that the hole or tunnel the cable goes through is on an incline and the tunnel is not a considtant height all the way through. When I insert the cable through the back, the front of the cable hits the ramp going up. through the front it hits the roof where it’s leveled out and it’s a tight fit. Hope this helps. Thanks again for the design. I absolutely love it.
0
Reply
printed well using marble PLA, tight fit for usb cable.
The designer has replied
1
Reply
WOW! Looks amazing!
0
Reply
I love this design. Took about 17 hours to print with 2 colors. It was just over 24 hours to make the PlayStation logo full original colors.
The only issue I have with it is that I can’t fit any USB-C cables I have through the hole for it on the back. It’s not a big deal to just run the cable over the top for me, at least until I find one that fits.
Thank you so much. I love it.
(If only I could find a Steam Deck dock that matched this design)
(Edited)
The designer has replied
1
Reply
Hello Lyphted, sorry to hear that you has some trouble with the cable. In France, the USB cable fits perfectly with this hole. It is a 5.7mmx12.7mm.
In order to improve the model, I created a new version with an independant adaptator for the USB cable, available in several size. You can find it here:
https://makerworld.com/models/211797
0
Reply
Print Profile
0.08mm layer, 2 walls, 10% infill
printed in pla-cf black & grey
great design! thank you
1
Reply
Do you have a photo with the playstation portal?
0
Reply
Print Profile
0.08mm layer, 2 walls, 10% infill
nice. thanks
0
Reply
Do you have a photo with the playstation portal?
0
Reply
Print Profile
0.08mm layer, 2 walls, 10% infill
Perfect accessory for my ps portal looks great 👍🏽
0
Reply
Print Profile
0.08mm layer, 2 walls, 10% infill
Great stand for the PlayStation Portal. I am unable to get the USB C cable to fit however.
The designer has replied
0
Reply
Oh, looks strange because i added additional free space between the hole and the USB head, after testing it...
0
Reply
Replying to @MaDutt
The USB C cable I’m trying to use is the one that came with the PlayStation Portal. It’s pretty close, but it doesn’t fit even if I try to force it. Do you happen to have another cable you recommend using?
0
Reply
Thank you for your comment. Could you please tell me how many tenth of a millimeter you would add ideally?
Thank you.
0
Reply
for the A1 mini? 😢
The designer has replied
0
Reply
i will have a look on it next week!
keep you inform 😉
0
Reply
Replying to @MaDutt
thank you☺️
0
Reply
Replying to @MaDutt
not possible? :(
0
Reply
Print Profile
0.08mm layer, 2 walls, 10% infill
0
Reply
USB C cable doesn't fit.
The designer has replied
0
Reply
Thank you for your comment. Could you please tell me how many tenth of a millimeter you would add ideally? I will add an update.
0
Reply
Replying to @MaDutt
Hello, sorry to hear that you has some trouble with the cable. In France, the USB cable fits perfectly with this hole. It is a 5.7mmx12.7mm.
In order to improve the model, I created a new version with an independant adaptator for the USB cable, available in several size. You can find it here:
https://makerworld.com/models/211797
0
Reply
License
This user content is licensed under a Standard Digital File License.
You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.
Related Models
© 2024 MakerWorld