Light Saber Lite (Collapsible) | LS01 by SavageLau

SavageLau

Toys & Games>Other Toys & Games

Print Profile(2)

All

A1 mini

P1S

P1P

X1 Carbon

X1E

colored, internal, external, cap&base in separate plates

Designer

5.9 h

3 plates

4.8(14)

Single color, internal & external parts in separate plates

Designer

4.9 h

2 plates

4.1(15)

Boost

138

205

384

537

Released

Description

If you want a commercial license, check out my bio and get it from Patreon.

This is simple version of Ultimate light sword. For people who does not want to have all the CAT light things in there. Just an simple Saber design. This is first one of my series of saber desing.

This Saber takes around 4h35m to print on X1C, takes around 105g of filaments.

Material Suggestions:

I Highly suggest to use Glow in the dark filament or Translucent filament for the internal parts, and pick any color you like for the external shell.

For external parts, DO NOT USE SOME BRITTLE silk filaments, it will break very easily. Some silk filaments will have very poor layer adhesion due to high speed printing cause part failure.

Post Work:

You will need to remove brims on both internal and external parts. Brim was added on all the printing profile to ensure the printing success rate. Print without brim is not recommaned.

Installation:

After you clean all the brims. follow these steps show on the gif.

Design:

This is a simple version of the ultimate light sword. I made a few design change on both internal and external to improve overall printing quality and have a slight different look.

Comment & Rating (35)

@maxence.chesnay

Print Profile

colored, internal, external, cap&base in separate plates

beautiful 3d model just a little tight for fitting

@ScouterTYTY39

Boosted

Print Profile

colored, internal, external, cap&base in separate plates

Printed great on a1 mini but lost top cap and haven't reprinted it yet.

@ceros

Print Profile

colored, internal, external, cap&base in separate plates

Printed very well on a A1 Mini. I duplicated the bottom part and merged them together to make a double-sided lightsaber only using Bambu Studio. Only the top round part that goes around where the blades are were extremely difficult to insert.

@Hero

Print Profile

colored, internal, external, cap&base in separate plates

Project are great and look awesome. Fast print but had problems with model that can't slice "smooth" and causing brim on side.

@prototypefab

hello, do you know if this would work scaled down? I'd like to print something like this for a kid, so I'd want it to be smaller, but i also like this more over your wands because you can swap broken inner pieces, which are gonna happen often if given to a kid

The designer has replied

@SavageLau

80% to 100% should work

@TomdeGroot

This is very cool!

@benmillercarson

Print Profile

colored, internal, external, cap&base in separate plates

it works amazing thanks

@user_3630610590

Boosted

terrible every thing got stuck it’s pain really bad waste of filament

@chefk85

Fun design. My kid loves it. The first big segment tries to pop out though so maybe could ad a couple little tabs or make it thicker at the base to keep it from sliding out so easily. Printed on Bambu p1s

@Oliverm769

Print Profile

Single color, internal & external parts in separate plates

Great model! worked well the first time

License

This work is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.