The one ring - The Lord of the Rings
The one ring - The Lord of the Rings
Boost
902
1408
208
GIF
Print Profile(3)
v2 - 0.12mm layer, 2 walls, 15% infill
Designer
7.9 h
2 plates
v1.1 - With optional back plate - 0.12mm layer, 2 walls, 15% infill
Designer
7.6 h
2 plates
v1.1 - 0.12mm layer, 2 walls, 15% infill
Designer
6.9 h
1 plate
Boost
902
1408
208
45
1.3 k
926
Released
Description
The one ring, need I say more?
Hang on the wall or just put it on a table. The ring is a whole 160mm in diameter!
I printed with Bambu PLA silk - Gold.
Current version 2.0 - Now better shine!
Warning, the new back plate is much more secured when inserted. Make sure led is installed before closing.
The assembly is easy, just take about 50cm led strip and put it in the ring, like this:
Or alternative slide it in above the internal “bride”, this way you can get two loops for more light.
Holder remix
If you want a stand take a look at this remix: https://makerworld.com/en/models/467240#profileId-376287
Revisions:
v 2.0
Total redesign of the inner space of the ring and the back plate. The led strip is now held in place which gives a more uniform shine. Slightly bigger radius on the top of the ring.
The back plate also snaps to the ring better, DON'T PUT ON UNTIL LED IS INSERTED.
v 1.1
- Added a optional back plate that snaps in place. Use the chord for hanging on wall, or drill a hole for a nail (or use bambu studio and add a hole)
Comment & Rating (208)
All
Boosted
Great model! Printed in gold silk PLA and attached to a carved wooden board. The small "button" below is a SR-602 PIR sensor which activates the light glow for a minute when motion is detected.
The designer has replied
9
Reply
wow, love the idea! imma make one!
0
Reply
how does yours look red and glowing if its gold silk? Is it a red or orange light inside?
0
Reply
Very nice! Printed with Sunlu Gold Silk PLA and a light strip from Amazon...
The designer has replied
6
Reply
looks great! I think you used a better ligth strip than me.
0
Reply
which light strip did you use - do you want to share the link? thanks in advance
0
Reply
Replying to @mreichert75
Lepro Bright White LED Strip Light 10M (2x5M), 2x2300lm 6000K LED Tape Light, Stick-on LED Lights for Kitchen Under Cabinet (12V Power Supply Not Included) https://amzn.eu/d/hy47BCW
3
Reply
I Can't Get It To Print, Have tried At least 4 times and no go, i did scale it up to 150% and printed it 3 times, then i re downloaded it again, tried at 100% and still no dice, so i think everyone here, there pants are on fire!!!
The designer has replied
0
Reply
Hey man, sad to hear :( But, at a quick glance I can se you have sliced it yourself. For one, you should absolutely not use support and I can see both have internal support! Second, did you properly dry your filament? Third, weird accusation when there is so many others pictures with successful prints.
Recommending, dry your filament! Slow down print speed, don't use supports.
11
Reply
and I used supports because I scaled it up!!
0
Reply
Boosted
Replying to @nootin3
Have you ever tried cleaning your plate between prints!? You clearly need some guidance in what you're doing. lol
8
Reply
Print Profile
v1.1 - 0.12mm layer, 2 walls, 15% infill
schwarz war nicht die beste Wahl 🤣
5
Reply
Boosted
Dabeisein ist alles 😂😂😂👍
0
Reply
Replying to @ChristoT
lol safe ja 🤣
0
Reply
Boosted
Print Profile
v2 - 0.12mm layer, 2 walls, 15% infill
Very nice, add a 2m cob-light with 5V insight
The designer has replied
2
Reply
thanks fellow winner! :)
(Edited)2
Reply
Boosted
What light did you use?
0
Reply
Boosted
Replying to @doxiedad06
https://amzn.eu/d/1FCD70u
(Edited)1
Reply
Boosted
Print Profile
v2 - 0.12mm layer, 2 walls, 15% infill
awesome design, would like for the letters to be hidden when lights off though, maybe a few more walls would do?
The designer has replied
0
Reply
not sure how much light would be blocked. think it will need a couple more walls to hide when turned off. perhaps v3 :)
0
Reply
Boosted
Replying to @christofer.jh
When in studio, I added a 3rd wall yet it seemed like, irrespectively, it kept only one (1) wall where the lettering are. May be something you could fix on v3!
0
Reply
Replying to @Mythical3DPrint
yeah, it would be needed to be changed in the model. Sadly I don't have the correct filament to try now before a vacation trip :/
0
Reply
Boosted
Print Profile
v2 - 0.12mm layer, 2 walls, 15% infill
Super model, looks amazing, really amazing in the dark. To hide the stitching area, I´m using one Holder in this place, nice model.
1
Reply
Can you please provide where you got this stand?
(Edited)1
Reply
Boosted
Replying to @PetrDDD
My own Design 🥰😎. You can find it Here: https://makerworld.com/en/models/467240#profileId-376287
Theresia are two Version of them with difference in heights (100mm and 200mm).
Otherwise Click on my Name, under my Profile You can find this holder together with other Designs from Me 😊
(Edited)1
Reply
Print Profile
v2 - 0.12mm layer, 2 walls, 15% infill
Printed very well. had some ringing but I guess there is no way around it unless you slow it even further
The designer has replied
1
Reply
how fast did you run? have not seen that kind of ringing on mine or others prints.
0
Reply
u might wanna tune your flow rate because it looks almost like a layer shift however it wouldnt have been 50 layer shifts so... possibly over extrusion. another option would be to download orca slicer and try out the feature called "accurate exterior walls" just a thought
0
Reply
Print Profile
v1.1 - With optional back plate - 0.12mm layer, 2 walls, 15% infill
Printed with no issues. Used Sunlu silk gold pla
The designer has replied
1
Reply
looks great!
0
Reply
Yes I like it, thanks for sharing your model!
(Edited)2
Reply
Boosted
Print Profile
v2 - 0.12mm layer, 2 walls, 15% infill
printed great.
2
Reply
License
This user content is licensed under a
Creative Commons Attribution-Noncommercial-Share AlikeRelated Models
© 2024 MakerWorld