Hufflepuff Lightbox | Harry Potter by Valeria Momo

Valeria Momo

Art>Other Art Models

Print Profile(3)

All

X1 Carbon

P1S

P1P

X1E

A1 mini

0.2mm layer, 2 walls, 15% infill

4.9 h

2 plates

5.0(12)

Arachne version-no gaps

3.4 h

1 plate

2.0(1)

Rectangular LED slot, 0.2mm, half speed, reduced size A1M

2.8 h

2 plates

Boost

107

197

215

127

Released

Description

My BambuStudio AMS ready print profile is loaded in the "Raw Model File" section. If you print the profile I would be happy if you will upload it as a new print profile.

Harry Potter Hufflepuff Lightbox. It has 2 holes at the back for hanging on the wall. I suggest using 5v led (It has a hole to pass the LED cable through). Size: 20*16*3 cm (check my Harry Potter Collection!)

Lightbox Desk Stand

If you want to hang the lightbox on your desk or shelf, try my Lightbox Desk Stand.

Commercial license

Do you want to sell prints of this model? You can purchase commercial licensing for this model by joining the Commercial License in my Patreon.

Comment & Rating (22)

@xbadsakura

Thanks for the great model! I had to cut the hole for the cable bigger, too. But that was no problem and the result is really nice!

The designer has replied

@ValeriaMomo

it's very nice 🥰🥰🥰

@darkdelusions

This is a fantastic model, I printed this as present for my wife's birthday and she loved it. The only thing I wish was different is the power cord passthrough as most LED strips on Amazon have a USB cable attached and will require a soldering iron to mount the led strip. Printing suggestions: If you are printing this on X1C I would highly recommend using silent mode when printing the top, when I attempted to print this on standard I was getting a lot of defects or fist layer issues. Filament: Yellow: Sunlu - Pure Yellow PLA White: Sunlu - White Black: Anycubic Black Grey: Overture Grey

(Edited)

The designer has replied

@ValeriaMomo

Thank you for the feedback, love your print. I usually use LEDs that I personally solder to a usb cable, that's why the hole is small--but I see your point. For future lightboxes I will take into consideration. I would be happy if you would upload your printing profile :-)

(Edited)

@darkdelusions

Replying to @ValeriaMomo :

The LED Strip I bought on amazon was thin enough to slip through the hole so I didn't have to modify the back at all. The LED Strip I purchased where UVTaoYuan LED Strip lights. The only down side is the USB cable is a bit short but it would would great if you are displaying it on your desk.

@hidrocalido.12

Boosted

Print Profile

0.2mm layer, 2 walls, 15% infill

perfect!

@sheajusprints

Arachne profile version doesnt fit the back.

(Edited)

@LowkeySus

Print Profile

0.2mm layer, 2 walls, 15% infill

came out great! changed the colors a little but otherwise perfect.

@impresion3d__

Print Profile

0.2mm layer, 2 walls, 15% infill

Awesome and very easy to print

@marcopassarani1

Print Profile

0.2mm layer, 2 walls, 15% infill

super top

@vidguide

Print Profile

0.2mm layer, 2 walls, 15% infill

@Encrust3d

Why upload this as your original design when you clearly remixed it? https://www.thingiverse.com/thing:2131600/files

The designer has replied

@ValeriaMomo

hi, my lightboxes are created from scratch, it's not a remix. the model you published is very different, it is on multiple levels.. my lightbox is on only one level.