X1 - P1 glass Lid Riser by Officina23

Officina23

3D Printer>3D Printer Accessories

Print Profile(2)

All

X1 Carbon

P1S

P1P

X1E

X1C glass lid riser 0.6mm nozzle

Designer

5.8 h

3 plates

4.6(29)

0.4mm nozzle, 0.2mm layer, 6 walls, 25% infill

10.8 h

3 plates

4.7(33)

Boost

111

163

116

560

667

Released

Description

This is my version of X1C top glass riser, redesigned redesigned after testing some of the various solutions available online. The advantages of this accessory are that the PTFE tube no longer touches the glass, and there is no need to remove the upper glass when printing material that requires good cooling.

It is made up of individual interlocking elements, so you can remove everything as one block without the pieces falling into the printer.

I also designed clips to hang the Allen key, scraper and a pen.

If you need to print ABS, PA or other materials that require a closed chamber and you don't want to remove the riser, special sealants are available called (Holes Sealants for X1C glass Lid Riser) which you can download by clicking here.

Documentation (1)

Assembly Guide (1)

rendering_9a8ea887-0869-427b-a8ed-1368999d2de4.png

Comment & Rating (116)

@dreamer

Print Profile

X1C glass lid riser 0.6mm nozzle

Awesome design!

The designer has replied

@Officina23

I like the black/orange contrast!

(Edited)

@dreamer

Replying to @Officina23 :

thanks! :)

(Edited)

@Stephanaccessor

Print Profile

X1C glass lid riser 0.6mm nozzle

WOW! really perfect! easy and super fast to print, perfect fit! I like the square holes you used to attach a Pen, I used them to create a seat for my I.P.A. thank you!

The designer has replied

@Officina23

Thanks, you did a nice job. the holes are also used to apply sealants, if you have to print with a closed chamber (you will have seen them in the photo, if you need them you can find them among the models I have published)

@Stephanaccessor

Replying to @Officina23 :

Yes for sure i will print them tomorrow :)... thank you so much! Officina23 (Italiano?)

(Edited)

@Over_Izzy

Print Profile

X1C glass lid riser 0.6mm nozzle

Printed well, my print came out just a little too long so either the front edge or the back edge doesn't sit where it's supposed to be.

(Edited)

The designer has replied

@Officina23

Strange, because the riser once assembled should be at least 1 millimeter smaller on each side. Or maybe you reversed the central lateral segments with the front and rear ones?

@Over_Izzy

Replying to @Officina23 :

maybe something changed when i switched to P1S 4mm nozzle

(Edited)

@braydenjfehr

It printed perfectly for me. The connectors are a bit tight, and my thumb was definitely sore after getting the last one in, but the final structure is nice and rigid. It's a nice solution to having the AMS top mounted while also allowing ventilation. I mainly print in PLA and PETG so I'll hold off on printing the covers unless I start working with a filament that needs a sealed chamber. Thank you so much for modelling this!

(Edited)

The designer has replied

@Officina23

Hello, thanks for your comment. I confirm that the connectors are very tight, I had to make them so tight to obtain a completely rigid piece, otherwise during the prints it would have influenced the vibrations in an unpredictable way, distorting the self-calibration of the resonance with consequent quality problems. Some people preferred to mount the connectors with the help of a hammer, and they're not wrong!

@Pain_Free

Review: This printed very well for me. I really enjoyed everything about my print. I printed in a Matte Black and Matte Green. It is almost 100% the correct measurement. Observations There was a little play on the top of the printer and the glass was ultra snug. I am using the Bambu Lab LEDS and they stuck along the top and the bottom of the inside (just above/below each air vent). I think that if I were to remake this then it would be to be a little taller so I could fit in an entire light strip. Maybe I will just print another one and plug up all the holes. I tried other riser models and this one is overall perfect just as it is in my opinion.

The designer has replied

@Officina23

Thank you for the review, I take note of your comments to improve the model.

@slamlhew

Fits together perfectly. Great print!

The designer has replied

@Officina23

Thanks

@oakbuffalo13676

Print Profile

X1C glass lid riser 0.6mm nozzle

Perfect fit and no concerns over quality or strength. I did not need to use any supports for the bridging, either.

The designer has replied

@Officina23

Thanks

@nixionus

Print Profile

0.4mm nozzle, 0.2mm layer, 6 walls, 25% infill

Fits nicely, printed in PLA, I hope it will resist hi temp prints.

@user_3814793868

I printed this for my X1C and it turned out great. Others have said no supports were needed but I was skeptical but I decided to go for it. I was very surprised how the printer as able to print across the almost one inch gap w/o supports. No problem....

@andrewgrussling

Boosted

Print Profile

0.4mm nozzle, 0.2mm layer, 6 walls, 25% infill

Printed very well even without supports. Had to hammer in the bow ties but the overall print is very sturdy. This helps me to be able to run a usb extension for an inlet fan without the glass damaging my cable. Printed in duramic glow in the dark pla.

License

This work is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.