Build Plate Guide - The Fuss Free Way For Build Plate Alignment

Build Plate Guide - The Fuss Free Way For Build Plate Alignment

Boost
493
1159
366
GIF

Print Profile(2)

All
X1 Carbon
P1S
P1P
X1
X1E
A1

PETG 0.2mm layer, 3 walls, 15% infill
PETG 0.2mm layer, 3 walls, 15% infill
Designer
23 min
1 plate
4.9(221)

PETG sx+dx- 0.2mm layer, 3 walls, 25% infill
PETG sx+dx- 0.2mm layer, 3 walls, 25% infill
30 min
1 plate
4.8(39)

Boost
493
1159
366
3
2.4 k
1.7 k
Released

Description

Build Plate Guide For your X1 & P1 Series Printers.

I have created my own version of a build plate guide,
It's been in use for over a month & is working fantastic.

1. Print in your chosen material, best in PETG
2. Remove supports

3. Clip onto the left back corner of the build plate ( should be a completely flush finish )

4. enjoy easy plate alignment

Comment & Rating (366)

Please fill in your opinion
(0/5000)

Hello, I'm the creator of the “Shifty” which is the original build plate centering tool. Please note, I don't allow remixes. https://makerworld.com/en/models/83480#profileId-89128 Thank you to all those who support my work by downloading the genuine “Shifty” directly from me at the link above.
(Edited)
The designer has replied
13
Reply
This is not a remix, this is my own version. You cannot license a clip/guide/shifter, your design has not been remixed as it doesn't contain one piece of your design. Just because it achieves the same goal doesn't mean you claim any rights to a different design.
41
Reply
Replying to @TotalChaos :
The methods for attaching it are the same as the Shifty (front tab, back hook, top and bottom rails, etc). This is my original concept, idea, and execution. You clearly looked at all my engineering and copied all the critical mounting methods, which is effectively a remix of all my development/solutions.
(Edited)
12
Reply
Replying to @JDJDJD :
The idea isn't that complicated, though. Unless you patented it (which I doubt), there's nothing wrong with replicating a similar design without using your own mesh. Yes, the guy's topology is weird at places, but still nothing criminal there.
(Edited)
31
Reply
Print Profile
PETG sx+dx- 0.2mm layer, 3 walls, 25% infill
das linke ist mir immer wieder gebrochen. Gedruckt mit PETG.
(Edited)
The designer has replied
0
Reply
Schauen Sie, ich habe sie in PETG gedruckt und sie sind perfekt. Haben Sie etwas geändert oder haben Sie alte oder feuchte Filamente?
0
Reply
Kann ich ein Foto des kaputten Teils haben?
0
Reply
Das Filament ist etwas älter, habe aber auch sndere gedruckt ohne Probleme
(Edited)
0
Reply
Print Profile
PETG sx+dx- 0.2mm layer, 3 walls, 25% infill
Ein Punkt, welcher mich seit Beginn aufgeregt hat, war die Positionierung der Druckplatte. Durch dieses kleine aber feine Add-On geht das fast von selbst. Genial und perfekt, danke für das Design. (beim entfernen des Supports zu ungeschickt und dumm gewesen und mir gleich mal in den Finger geschnitzt... 😕, selber schuld 😅 )
The designer has replied
2
Reply
thanks
(Edited)
2
Reply
Print Profile
PETG 0.2mm layer, 3 walls, 15% infill
passt und erfüllt voll und ganz seinen Zweck. Die Druckplatte findet sich perfekt auf dem Druckbett.
The designer has replied
1
Reply
Thanks for the comment and 5* rating :)
0
Reply
Replying to @TotalChaos :
Translation "fits and fully fulfills its purpose. The printing plate fits perfectly on the print bed."
0
Reply
Print Profile
PETG sx+dx- 0.2mm layer, 3 walls, 25% infill
Alles super ( PETG ).
The designer has replied
1
Reply
thanks
(Edited)
1
Reply
Print Profile
PETG sx+dx- 0.2mm layer, 3 walls, 25% infill
il piatto entra bene
The designer has replied
1
Reply
thanks
(Edited)
1
Reply
Print Profile
PETG sx+dx- 0.2mm layer, 3 walls, 25% infill
Buen diseño!
The designer has replied
1
Reply
thanks
(Edited)
1
Reply
Print Profile
PETG 0.2mm layer, 3 walls, 15% infill
In gray ASA. Not only looks like it is part of the printer, but should have been there in the first place. Really makes it easy to load a build plate.
(Edited)
The designer has replied
1
Reply
looks great :) thanks for the 5* rating
0
Reply
Print Profile
PETG 0.2mm layer, 3 walls, 15% infill
Super handy design. you wouldn't expect just how much you needed these until you try them . I had zero problems printing from my Cellphone while I was 1600 miles from my X1C . I used Bambu PETG and whatever settings the Designer built in to file. Thank you for your time it's appreciated. peace ✌️
1
Reply
Print Profile
PETG 0.2mm layer, 3 walls, 15% infill
easy to Print,Looks great, fits perfekt 👍
1
Reply

License

This work is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.