Flipper zero case

Copyright Claim

Flipper zero case

Boost
95
141
37

Print Profile(2)

All
X1 Carbon
P1S
P1P
X1
X1E
A1
A1 mini

0.16mm layer, 2 walls, 15% infill
0.16mm layer, 2 walls, 15% infill
Designer
1.3 h
1 plate
4.3(25)

A1 mini, 0.16mm layer, 2 walls, 15% infill
A1 mini, 0.16mm layer, 2 walls, 15% infill
1.4 h
1 plate

Boost
95
141
37
9
393
259
Released

Description

as this is NOT behind a paywall, your support would be appreciated!

https://www.paypal.com/paypalme/zrcrackiin

*********************************************************

MASSIVE SHOUTOUT TO TALKING SASQUACH FOR THE REVIEW/ HOW TO GUIDE!

https://www.youtube.com/watch?v=pLYcAfp5PMc

 

*********************************************************

***UPDATED 18/09/2023***

  1. Pcbway Case Set
  • Optimised case set for PCBWAY this is front v3 and rear v1 in one file ready to be uploaded and ordered, scailing pre done so you don't need to.

*********************************************************

***UPDATED 13/09/2023***

  1. Front Case v3
  • Opened up GPIO holes to 1.4x1.4mm as a revision to allow for resin prints with clear coat applied on top

*********************************************************

***UPDATED 27/08/2023***

  1. Front Case v2
  • Opened up GPIO holes to 1.0x1.0mm to allow easier board insertion.

*********************************************************

 

Replacement case for flipper zero.

Confirmed good fitment on my own personal flipper, and various others in the community.

 

To allow for manufacturing tolerances of the flipper, bump the scale to 100.29% respectively

beware of your iButton pins, i take no responsibility for you breaking them, it fits mine so it SHOULD fit yours.

seams are a little tight but it fits well.

Screen window sits in place (you can glue if you want)

IR Filter will fit in place also.

i spent a long long time making this happen, and i didn't want to butcher things like everyone else who “made one”

your window and IR filter will fit, without cutting them or shaving them down.

printed on a X1C @ 0.08 layer height

 

 

 

as this is NOT behind a paywall, your support would be appreciated!

https://www.paypal.com/paypalme/zrcrackiin

Comment & Rating (37)

Please fill in your opinion
(0/5000)

Print Profile
0.16mm layer, 2 walls, 15% infill
Trying to print in transparent PETG. The model seems very accurate but using the recommended settings and the recommended print profile resulted in an unusable case. I would blame these issues on the filament but it's possible the print profile isn't set up with the best support options for this model. Might try again with PLA to see if it comes out usable.
The designer has replied
0
Reply
Not sure how yours has come out like that, could be that it's petg, my pla ones have cone out great, the only difficult part is printing with support around the ibutton area
0
Reply
Replying to @ZR_CrackiiN :
Opening the profile had support enabled so I used the settings that were pre-set in the profile. Is that your recommended settings? I've had successful prints with this same PETG but it seems mostly around the support area at the 0.08 layer height that I think made the supports all fuse more strongly with the model.
0
Reply
Replying to @wyld :
its possible that you're right on the money with .08 and supports yeah those settings for support work great with pla for me
0
Reply
Print Profile
0.16mm layer, 2 walls, 15% infill
Took me a couple tries, rough support. Model worked nice.
0
Reply
Print Profile
0.16mm layer, 2 walls, 15% infill
Nice model, kudos! I haven’t confirmed scaling yet, I’m first focusing on finding perfect settings for transparent PETG and also for minimizing support scarring.
0
Reply
Print Profile
0.16mm layer, 2 walls, 15% infill
very happy with the design. Thanks!
0
Reply
Print Profile
0.16mm layer, 2 walls, 15% infill
prints nice but was to small
0
Reply
about to print this in transparent PETG. the latest version pre-scaled was still too small?
(Edited)
0
Reply
Replying to @wyld :
I'll try it out when I get home and let you know
(Edited)
1
Reply
Print Profile
0.16mm layer, 2 walls, 15% infill
NIce flipper mod
Support Issue
The designer has replied
0
Reply
sounds like user error...
0
Reply
@ZR_CrackiiN is this model meant for printing on X1C or for sending to PC Way for resin printing? I don't see any pictures of prints posted and some complaints that it was too small. About to try a print and curious your suggestions for making sure it fits properly if print on X1C. Thanks!
(Edited)
The designer has replied
0
Reply
use pre scaled version, fits great! those who complain that it doesn't fit didn't read the description ;)
1
Reply
Great Work <3
0
Reply
I'm freaking out how clear is the filament used in the photo. I'm curious which brand it is. petg?
0
Reply
Print Profile
0.16mm layer, 2 walls, 15% infill
Worked well and looks good, thanks.
0
Reply