Cutie Baby Turtle by squinn

squinn

Miniatures>Animals

Print Profile(18)

All

P1S

P1P

X1 Carbon

X1E

A1 mini

0.12mm layer, 2 walls, 15% infill

Designer

48 min

1 plate

4.9(600)

A1 Mini Profile, 0.12mm layer, 2 walls, 15% infill

Designer

1 h

1 plate

4.9(67)

Four Color Profile, 0.12mm layer, 2 walls, 15% infill

Designer

7.9 h

1 plate

4.9(22)

P1S, 26 min, 0.2mm layer, 2 walls, 5% infill

32 min

1 plate

4.9(32)

Click to see more

Boost

904

1370

935

4.4 k

5.9 k

Released

Description

A cute little baby turtle that looks great sitting up on two legs, standing on all four, or just laying down to get some rest.

This is an easy print-in-place that has been carefully designed to require no supports, and (at just 6 cm long) it's a fun size that only requires 14 grams of filament and prints quick.

Comment & Rating (935)

@chad.wansing

Print Profile

0.16mm layer, 2 walls, 6% infill, full pad 18 pieces

had multiple runs of between 1-3 turtles coming off the build plate. first layer seems to be slightly over-extruded but subsequent layers seem good and smooth. this is the first time I've had back-to-back runs of a model have problems ( center of front row and both sides of second row....filament in the back is leftovers from the pile of spaghetti resulting from the first run)

The designer has replied

@riso20411

I'm sorry what happened to you. But the fact that your model does not hold on the mat (low temperature or greasy bed) and that you have a poorly calibrated Flow on the filament is not a bad profile that I am uploading. that's why I'm sorry that you gave it two stars.

(Edited)

@chad.wansing

bed at 60* C, cleaned after every run (soapy water followed by IPA) and been printing over a year, so no, it wasn't a cold or greasy bed. I specifically used filament that I've put several hundred hours into printing with (under a contract for a local business) as it was my best tuned filament. Perhaps your next argument will be "wet filament", again, no. Look, nothing personal, and maybe these settings work perfectly on your machine, but for me and my P1S, this print was unsuccessful with your settings.

@JavyPrints

Replying to @chad.wansing :

So, what settings did you change to make it work?

@JayRay

A whole family. 100 to 400%

The designer has replied

@squinn

Love how you setup these four sizes, and your prints came out so beautifully smooth! Thanks much for sharing your make here.

@JayRay

Replying to @squinn :

my kids love them. I actually have two of the large ones, it just didn't make the family photo.

@ToolsoftheTrade

The print profile is no longer public

Good and accurate profile. printed two of these with good quality and a smooth finish.

The designer has replied

@Settlers

Great to see! Thanks for the feedback 😄👌🏻

(Edited)

@Dursun

Print Profile

Turtle 0.10 to 0.16mm layer, Ironed, 2 walls, 15% infill

Super leicht zu drucken

@Romeo260

Print Profile

Turtle 0.10 to 0.16mm layer, Ironed, 2 walls, 15% infill

Hammer geil die kleinen

@Joshlehman

The print profile is no longer public

nice easy print

@user_2989893637

Thank you for the design, super cute! Filament: Fashion3d silk pla plus

@Tymotion

The print profile is no longer public

Beautiful

@mitchg

The print profile is no longer public

I thought my wife or daughter would dig these turtles, but I think I’ve created a battle as they both are fighting over them. 1st one was on a rainbow pla and my daughter wants that color combination but It is hard to reproduce the same as the roll changes! Ncely done!