Print-in-place and articulated F14 Jet Fighter with Improved Wingdesign by agepbiz

agepbiz

Hobby & DIY>Vehicles

Print Profile(2)

All

X1 Carbon

P1S

P1P

X1E

A1 mini

0.2mm layer, 2 walls, 15% infill

Designer

46 min

1 plate

4.7(231)

A1 Mini - 0.2mm layer, 2 walls, 15% infill

1.1 h

1 plate

4.8(18)

Boost

494

863

304

2 k

Released

Description

I have been experimenting with a breakaway wingtip to improve on the silhouette of my design to match the real F14 better, while still being print-in-place and articulated. The wingtip breaks of with a satisfying snap and leaves a nice clean edge. I have also adjusted the wing shape and the angle of the tail fins. I have also included a version with a brim

Commercial license

Do you want to sell prints of this model? You can purchase commercial licensing for this model by joining the Commercial license tier in my club

added a larger version (300). If you want to print the stands for it you have to upscale the stands to 150%

Subscribe or follow me on:

Instagram: www.instagram.com/agepbiz

YouTube: www.youtube.com/user/agepbiz

Twitter: www.twitter.com/agepbiz

Printsettings:

No support
No raft
0,15mm-0,2mm layer height
35-45mm/s

printinplace

f14

topgun

Comment & Rating (304)

@matthewpgallagh

Print Profile

Fine Settings - 0.12mm layer, 3 walls, 15% infill

Nice model but had an issue with one of the wings not printing correctly

The designer has replied

@kvnper

hi, I am the print profile uploader, I'm sorry about the wing, I will keep an eye on this if it's a common issue

(Edited)

@andy.hartland

Same issue

@kvnper

Replying to @andy.hartland :

Hi Andy, sorry, I only saw this now, I didn't get a notification. Thanks for letting me know, I'll see what I can do about this.

(Edited)

@3Dreamworld

Boosted

Print Profile

A1 Mini - 0.2mm layer, 2 walls, 15% infill

The print model is fantastic overall, with impressive design and mechanical structure. However, I suggest printing near an 8mm cylinder for optimal finishing of the plane's tip. It's crucial to handle the wings with care during printing and when removing the object from the print bed to prevent breakage. Overall, with attention to detail during printing and handling, the final result will be impeccable.

@Salvatore_T

thanks so much for the advice! I printed f14 with the cylinder as you recommended and I must say that the finish was truly excellent!!! really good

@davis.338lapua

Print Profile

0.2mm layer, 2 walls, 15% infill

printed perfect but I was heavy handed removing the brim and broke a wing tip off I also round off the nose a bit since I gave it too my kid to play with and it was really pointy.

@mkjlidstrom

As far as I understand it the tips are supposed to be broken off at the line! So your "broken" wing is actually the correct one :)

(Edited)

@davis.338lapua

Replying to @mkjlidstrom :

lol well now I feel dumb , you're correct.

@omrihillel

Print Profile

FAST 43 Minute Print!, 0.2mm layer, 2 walls, 15% infill

a little bit of sogging on the wing cavity but I was still super surprised from the amazing design of tolerances and support

@Adamko

Print Profile

Fine Settings - 0.12mm layer, 3 walls, 15% infill

worked perfectly on first try with spectrum silver PLA

@mjharrop

Print Profile

0.2mm layer, 2 walls, 15% infill

great design, works as promised. printed 15 at a time for a kids program prize bucket. printed stable with easy brim removal. will be printing again soon .

@Waters

Print Profile

0.2mm layer, 2 walls, 15% infill

printed with EPA. fast PLA Black, had some minor stringing on the default Generic Fast PLA profile but other than that it printed perfectly! was a little stiff after printing but after a few cycles of the wings they move great!