HSW Accessory Set / Attachment Connector Parts
Remixed by
Copyright Claim
HSW Accessory Set / Attachment Connector Parts
Remixed by
Boost
101
268
83
Print Profile(2)
0.2mm layer, 6 walls, 25% infill
Designer
4.6 h
2 plates
0.2mm layer, 6 walls, 25% infill
5.1 h
2 plates
Boost
101
268
83
1
617
983
Released
Description
I recreated these with a little thicker top to increase rigidity on the multiple connectors.
I have included the STEP files in case you would like to make your own modifications.
- Single Connector
- Single Connector for drywall screw mounting
- Single Connector for 10mm magnet
- Single Connector for 15mm magnet
- Double Connector
- Double Connector for drywall screw mounting
- Double Connector for 10mm magnet
- Double Connector for 15mm magnet
- Triple Connector
- Triple Connector for drywall screw mounting
- Quad Connector
- Quad Connector for drywall screw mounting (orientation #1)
- Quad Connector for drywall screw mounting (orientation #2)
I also included a plate with rotated orientation for the following:
- Single Connector
- Double Connector
- Triple Connector
- Quad Connector
Comment & Rating (83)
All
Print Profile
0.2mm layer, 6 walls, 25% infill
most of them print but the singles always have an issue for some reason
The designer has replied
0
Reply
What material are you printing with? I ran two sets in PLA yesterday and had no issue. I am using Bambu P1S. It also appears you are trying to use support. I do not use support on the pieces with the open hex. On the others, I only support the area inside the circle. If you use support in the main geometry, it will make a mess and be hard to remove everything. See the two pics I included.
Hope this helps. :)
(Edited)
1
Reply
Replying to @pstov
I am using Bambu glow in the dark PLA on a p1s. I might try and print one of these in something else and give you feedback.
0
Reply
Replying to @Huni
I am interested to know how this worked out. Is it possible the print is not adhering to the bed well?
0
Reply
The pieces don't seem to be connected properly in the drawing. Rather than be fused together in 1 piece, It's like they are sectioned off and just pushed together which makes them snap VERY easily after printing.
The designer has replied
1
Reply
Are you using a 0.4 nozzle? I printed on 0.2mm layers and 25% infill. I use them all the time and they work fine.
0
Reply
Print Profile
0.2mm layer, 6 walls, 25% infill
Pieces printed perfect and work great in the honeycomb wall
1
Reply
Print Profile
0.2mm layer, 6 walls, 25% infill
Perfect fit.
thank you!
1
Reply
Print Profile
0.2mm layer, 6 walls, 25% infill
printed flat, ended successfully with no issues. not useful for anything
Missing Model Parts
The designer has replied
0
Reply
Sorry to hear you had trouble. I am not sure what happened here. There are many users who successfully use these connectors.
0
Reply
Print Profile
0.2mm layer, 6 walls, 25% infill
PRINTED GREAT TY
1
Reply
Print Profile
0.2mm layer, 6 walls, 25% infill
works perfectly
1
Reply
Print Profile
0.2mm layer, 6 walls, 25% infill
les attaches doubles, cassent très facilement
0
Reply
Print Profile
0.2mm layer, 6 walls, 25% infill
All Ok 100%
0
Reply
Print Profile
0.2mm layer, 6 walls, 25% infill
the two hex pieces aren't particularly strong between the shapes and will seperate quite easily. take care in pressing with a flat item to ensure it locks in straight, this will reduce the likelihood of seperation.
Otherwise, the design is tight and prints clean, I will continue to use these on my HSW
2
Reply
This remix is based on
License
This work is licensed under a
Creative Commons Attribution-NoncommercialRelated Models
© 2024 MakerWorld