Dualsense adjustable phone holder PS5 Remote play by dziobasty

dziobasty

Hobby & DIY>Electronics

Print Profile(5)

All

P1S

P1P

X1 Carbon

X1E

0.2mm layer, 3 walls, 45% infill

Designer

1.4 h

1 plate

4.8(6)

FOR IPHONE 0.2mm layer, 6 walls, 25% infill

Designer

4.2 h

1 plate

4.6(5)

FOR IPHONE without AMS 0.2mm layer, 6 walls, 25% infill

Designer

1.6 h

1 plate

5.0(3)

FOR OTHER PHONES 0.2mm layer, 6 walls, 25% infill

Designer

4.1 h

1 plate

3.0(1)

Click to see more

Open in Bambu Studio

Boost

190

135

Released

Description

Adjustable phone holder for dualsense.
Fits phones and tablets with a width ranging from 73mm to 107mm
If your phone is 73 to 84mm wide, please choose the MAX screw
Screw for base print 2psc.
You can use AMS to fill the PS logo with a different color.

There is a version adapted to iPhone 12, 12 pro, 12 pro max,13, 13 pro, 13 pro max, 14, 14 pro, 14 pro max, 15, 15 pro, 15 pro max, and there is also a second design that should fit most other phones. If there are any problems, please let me know and I will improve the model. Unfortunately, I don't have an Android phone to check it.

Layer height: 0.2mm
Wall lops: 3
Infill: 45%
PLA

YOU MUST USE A SUPPORTS!

The screw with the letter R has a left-hand thread and must be screwed in on the right side

Comment & Rating (23)

@golferbobert

can you make an a1 mini print profile please? if you need to test it I can

(Edited)

@Rcarter04

Printing on A1 Mini? I'm currently printing this on my P1S, but I can definitely put together a slice for your mini if you'd like. Single colour on one plate?

@golferbobert

Replying to @Rcarter04 :

yes please

@user_2244687976

Boosted

Print Profile

FOR IPHONE 0.2mm layer, 6 walls, 25% infill

honestly works amazingly love the different angles it can be,the screws were a bit hard to put in but it works great once it’s assembled.

@rousavyfilip

the thread for the long tightening screw is printed incorrectly every time and I don't know if the error is in the screw or in the thread on the holder, the screw goes through the thread as if the screw was 0.5-1 mm smaller than it should be

The designer has replied

@dziobasty

I'll check it :)

@slackware87

Print Profile

FOR IPHONE 0.2mm layer, 6 walls, 25% infill

la vite di fissaggjo mi ha dato non pochi problemi stampata in petg, in pla tutto ok

The designer has replied

@dziobasty

Yes, because this printing profile is created for PLA :)

@Makers.m3D

Print Profile

FOR IPHONE 0.2mm layer, 6 walls, 25% infill

excelente!

@Makers.m3D

Print Profile

0.2mm layer, 3 walls, 45% infill

excelente!

@Rcarter04

Love the improvements you've made to this compared to the various other similar DualSense phone mount designs available. The detents added to the hinge interfaces fixes the most prominent issue with the various other designs, especially with heavier phones. I also really like the simple long-bolt phone width adjustment you've added here, it's significantly better than the couple of other adjustment designs I've seen. I do have a few improvements/fixes for the design: 1. The threading for the hinge bolts in both "Phone Holder Bottom" is reverse threaded on the right. This seems like it might have been an intentional decision to ensure the bolt does not loosen during use, so I'm assuming it was just a matter of forgetting to export the reverse threaded version as it is displayed with the correct logo orientation in your screenshots. Either separate "Hinge Bolt (Left)" and "Hinge Bolt (Right)" files or a combined "Hinge Bolt (L/R Pair)" file would be perfect. 2. The bolts should all be printed with a brim. The slicer automatically adds one to the long bolt, but not the short ones. 3. Could we get a version of the short bolts with the logo shape flush with the bottom surface? This would make getting a nice flat dual-colour logo finish using the painting tool much easier. 4. I recommend reducing the diameter of the bevel on the tips of the hinge bolts. Currently it basically finishes the thread with a complete flat ring around the tip, which makes it difficult to start threading it without some trimming.

The designer has replied

@dziobasty

Of course, no problem. I will improve the design in the coming days :)