Charmeleon - Pokemon by phyXoo

phyXoo

Miniatures>Creatures

Print Profile(3)

All

P1S

P1P

X1 Carbon

X1E

A1 mini

0.2mm layer, 2 walls, 15% infill

Designer

1.3 h

1 plate

4.7(19)

PLA 0.16mm

1.4 h

1 plate

4.0(3)

70mm high - 0.2mm layer, 3 walls, 10% infill

1.3 h

1 plate

3.5(2)

Open in Bambu Studio

Boost

154

294

214

Released

Description

40% scale model

0,2mm layer height

0,2mm Top Z distance - be careful when removing supports on hands.

Smoothened Top surfaces

charmeleon

pokemon

Comment & Rating (31)

@user_128984610

Print Profile

0.2mm layer, 2 walls, 15% infill

I printed this for my son as one of my first prints in PLA the tail broke off within a few minutes when he dropped it. I printed another in PETG and the tail broke off again. The bit just before the larger tail section is so small and a single hollow circle. I am new to 3d printing so not sure how to change it but need that small join to be filled in or stronger somehow.

The designer has replied

@phyXoo

Hello there, if you intend to print this for your son and he may occasionally drop it on the floor, I will recommend increase wall loops to 3 or 4 and increase infill a bit.

(Edited)

@user_128984610

Replying to @phyXoo :

Thanks for the info, I printed it again with the wall loops at 4 and infill at 30% seems stronger, Passed a simple drop test. Will see how it holds up. Thanks again.

@phyXoo

Replying to @user_128984610 :

Glad to help. :) If you need any more assistance, feel free to message me.

@cooleytime

Print Profile

0.2mm layer, 2 walls, 15% infill

claws broke off with supports

The designer has replied

@phyXoo

try removing supports in that area with pliers. worked like a charm with me. Sometines you need be careful with removing supports. 😕 pressed F 🫡 for the Charmelon.

(Edited)

@talha.arslan

Print Profile

0.2mm layer, 2 walls, 15% infill

very cool design! easy to print thank you for sharing

@PronouncedKeil

Print Profile

0.2mm layer, 2 walls, 15% infill

Printed for my son and the tail broke the first time he dropped it. Maybe just an issue with Charmeleon in general, but worth noting if you are printing for a kid. Unlike others, I found the supports easy to get with pliers.

@MG_Print

Print Profile

0.2mm layer, 2 walls, 15% infill

Super Druck!

@heres_greggy

Print Profile

70mm high - 0.2mm layer, 3 walls, 10% infill

printed two of them and painted once done! The flame on the tail breaks off a little too easy unfortunately, otherwise would have given five stars

@user_254649991

Print Profile

0.2mm layer, 2 walls, 15% infill

very nice

@gillmon99

Print Profile

0.2mm layer, 2 walls, 15% infill

vorsicht arme brechen schnell

@willymyz

Print Profile

0.2mm layer, 2 walls, 15% infill

Beautiful

@xyz1007

Print Profile

0.2mm layer, 2 walls, 15% infill

(Edited)

The designer has replied

@phyXoo

I haven’t had this problem at all. 😶 Did you carefully remove the supports ? It might happen when you just rip off the supports.

@xyz1007

Thanks for the fast response. I should have been more clear. The print was great and the supports removed easily. My son damaged the end of the tail playing with it. If you print it and don't play with it much it's perfect. The barb at the end of the tail is the weakest part.