Poop Pop Stop Large for P1S/P1P

Remixed by

Poop Pop Stop Large for P1S/P1P

Remixed by
Boost
583
1198
228

Print Profile(6)

All
P1S
P1P
X1
X1 Carbon
X1E
A1
A1 mini

0.16mm layer, 3 walls, 15% infill
0.16mm layer, 3 walls, 15% infill
Designer
39 min
1 plate
4.8(98)

0.16mm layer, 4 walls, 15% infill PETG
0.16mm layer, 4 walls, 15% infill PETG
31 min
1 plate
4.8(31)

PLA  - pla in P1P works just fine!
PLA - pla in P1P works just fine!
23 min
1 plate
4.7(37)

0.16mm layer, 4 walls, 15% infill ABS
0.16mm layer, 4 walls, 15% infill ABS
29 min
1 plate
4.6(8)
Click to see more

Open in Bambu Studio
Boost
583
1198
228
96
2.9 k
2.4 k
Released

Description

I remixed this model because I found it very useful, I had the problem that the waste stopped between the perimeter of the waste tray and the perimeter of the molded piece, I enlarged the waste space so that I could let the waste fall comfortably. Now I no longer have waste material on the print bed!

Thanks Downhill_Solutions!

Comment & Rating (228)

Please fill in your opinion
(0/5000)

Print Profile
0.16mm layer, 3 walls, 15% infill
It's a nice construction in itself, but unfortunately the poop shoot gets stuck. I tested it several times.
The designer has replied
1
Reply
do you have x1c or p1 series?
0
Reply
Replying to @spluca80 :
I have a X1C.
0
Reply
Replying to @Krall3 :
I haven't tried it on the X1C, if I can I'll try it and see if there are any changes to make. Thanks for the feedback
0
Reply
Print Profile
0.16mm layer, 3 walls, 15% infill
I printed with PETG and removed the rafts and still printed flawlessly. Supports did also remove without any issue. Seems to work, so far. Thanks!
The designer has replied
2
Reply
Nice color!
0
Reply
Sadly had to remove mid print for one print where I needed constant colour change, it kept clogging. The filament kept sticking to it. also noticed that it was getting discoloured not sure if it is because of the heat, probably PLA Matte was not a good choice for the job. i am using the save 60% filament profile for the print, it maybhave contributed to this but I see many other people talking about the same issue so just wanted to be transparent :)
(Edited)
The designer has replied
0
Reply
PLA is not recommended! you can print it in PERG, ASA, or ABS
1
Reply
Replying to @spluca80 :
I am using Tianrui's PETG-ECO, designer print settings, the filament still sticks to the build plate...
(Edited)
Show original
0
Reply
Replying to @user_1148015445 :
I spray a drizzle of spray oil in the drain pan, so that the waste material falls freely
0
Reply
Print Profile
PLA - pla in P1P works just fine!
A great model. Fits well, just a bit finicky to insert.
2
Reply
very tight fit
1
Reply
Print Profile
0.16mm layer, 3 walls, 15% infill
work great
The designer has replied
1
Reply
Thankyou!
0
Reply
Print Profile
0.16mm layer, 4 walls, 15% infill PETG
A great utility, it's gone on all three of my printers! Printed out of orange PETG. Pics are after over a month and hundreds of poops, only have had a handful of chute clogs, though I'm sure this has improved that statistic, I have noticed far fewer poos falling onto the bed plate when this is installed. Also, I have not had any issues with higher temp filaments sticking to the petg. Thought that might have been an issue but it has not been!
2
Reply
Print Profile
0.16mm layer, 3 walls, 15% infill
Top, Test mit 10 Layerwechsel 10/10 da gelandet wo sie sollen, und zwar in die Toi und nicht aufn Druckbett. Gedruzckt auf ein P1S mit ABS
The designer has replied
1
Reply
TOP!
0
Reply
Print Profile
0.16mm layer, 3 walls, 15% infill
Perfectly fitted, very good.
Show original
2
Reply
printed the original in PLA but poops stick to it and it’s not working well because of that but not poops inside the printer since installed. perhaps need to have a larger hole for pooping like your remix and it will not stick. nice design , I will give a try thanks a lot
(Edited)
The designer has replied
0
Reply
hello, print this remix in PETG, ASA or ABS; pla is not recommended
1
Reply
remix works great thanks
0
Reply
Boosted
Print Profile
0.16mm layer, 3 walls, 15% infill
Came out fine with Jayo PETG 👍🏻
1
Reply

This remix is based on

not existThe model does not exist anymore

License

This user content is licensed under a
Creative Commons Attribution-Noncommercial-Share Alike