Hexagonal Display Stand

I created hexagonal display stands in various sizes, ranging from 100mm to 220mm in height. All sizes use the same connector, which is 40mm long. With hexagonal display stands of different sizes, you can create a more dynamic display wall.

The size shown in the photo is 150mm, which is the maximum printable size for the A1 mini, designed specifically for the Cutie1 toy series.

There are currently five size versions available. If you need a smaller size, please let me know, and I will design an additional, smaller version.

I created hexagonal display stands in various sizes, ranging from 100mm to 220mm in height. All sizes use the same connector, which is 40mm long. With hexagonal display stands of different sizes, you can create a more dynamic display wall.

The size shown in the photo is 150mm, which is the maximum printable size for the A1 mini, designed specifically for the Cutie1 toy series.

There are currently five size versions available. If you need a smaller size, please let me know, and I will design an additional, smaller version.

---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

First of all, thank you everyone for supporting this model. When I first uploaded it, I wasn’t very familiar with MakerWorld’s file organization system, so each file only included a single size version. I’ll be reorganizing the print configurations and re-uploading the files.

### 2026/05/22 Update

I will be adding several new accessory modules for this model:

1. **Half Hexagon Honeycomb Module**
  A half-size hexagon honeycomb piece has been added. If you only need two rows, this module can be used to reinforce and extend the connection.

2. **90-Degree Connector Module**
  Two versions are provided:

  * A simple connector version that uses very little material.
  * A block-style connector version that uses more material but provides a much better overall appearance.

3. **Support Pin Modules**
  Two versions are available:

  * A double-sided tape version, which can be attached to the wall to reinforce certain parts of the upper hexagon modules and improve wall contact. It is not recommended to leave the entire honeycomb display structure suspended without support.
  * A screw-mount version for wall installation. If using this version, please use wall anchors. Heavy objects are still not recommended, so please pay attention to load capacity.

4. **Drawer Module**
  Some users requested drawer storage, so a drawer module has been added. Please consider weight limitations before use. It is recommended for storing lightweight model or toy accessories rather than heavy items.

5. **Added a wall-mount hanging module.**
  This module requires Part A to be mounted to the wall first, then Part B can be attached onto it. Using this module, you can connect and extend additional hexagonal units together.
Two types of hanging modules are provided. One version is designed to be mounted directly onto a wall using wall anchors and screws, while the other version supports the IKEA SKÅDIS pegboard system and can be attached directly using the dedicated locking clips. 

Please note that Part B has been specifically adjusted for the wall-mount module, so its thickness is 75mm. Combined with the 5mm thickness of Part A, the total thickness becomes 80mm, which matches the thickness of the original hexagonal unit. Please pay attention to this detail.

P.S. Currently, only the accessory modules for the 150mm version have been updated. If other sizes are needed, I will add them in future updates.

First of all, thank you everyone for supporting this model. When I first uploaded it, I wasn’t very familiar with MakerWorld’s file organization system, so each file only included a single size version. I’ll be reorganizing the print configurations and re-uploading the files.

### 2026/05/22 Update

I will be adding several new accessory modules for this model:

1. **Half Hexagon Honeycomb Module**
  A half-size hexagon honeycomb piece has been added. If you only need two rows, this module can be used to reinforce and extend the connection.

2. **90-Degree Connector Module**
  Two versions are provided:

  * A simple connector version that uses very little material.
  * A block-style connector version that uses more material but provides a much better overall appearance.

3. **Support Pin Modules**
  Two versions are available:

  * A double-sided tape version, which can be attached to the wall to reinforce certain parts of the upper hexagon modules and improve wall contact. It is not recommended to leave the entire honeycomb display structure suspended without support.
  * A screw-mount version for wall installation. If using this version, please use wall anchors. Heavy objects are still not recommended, so please pay attention to load capacity.

4. **Drawer Module**
  Some users requested drawer storage, so a drawer module has been added. Please consider weight limitations before use. It is recommended for storing lightweight model or toy accessories rather than heavy items.

5. **Added a wall-mount hanging module.**
  This module requires Part A to be mounted to the wall first, then Part B can be attached onto it. Using this module, you can connect and extend additional hexagonal units together.
Two types of hanging modules are provided. One version is designed to be mounted directly onto a wall using wall anchors and screws, while the other version supports the IKEA SKÅDIS pegboard system and can be attached directly using the dedicated locking clips. 

Please note that Part B has been specifically adjusted for the wall-mount module, so its thickness is 75mm. Combined with the 5mm thickness of Part A, the total thickness becomes 80mm, which matches the thickness of the original hexagonal unit. Please pay attention to this detail.

P.S. Currently, only the accessory modules for the 150mm version have been updated. If other sizes are needed, I will add them in future updates.

90-Degree Connector Module_1

90-Degree Connector Module_2

wall-mount hanging module

Supports IKEA SKÅDIS pegboard