My daughter printed this through the iPhone app on my P1S and absolutely loves it. The detail is amazing. 10/10 on the design! Thank you so much for sharing this 3D print!

This mini silica case is great for filling it with reusable silica beads. I had another print that produced a lot of waste. Instead of waste, I chose to print the waste into these mini silica cases. I now use the cases for my filament in ziploc bags. Thank you for designing and sharing this model!

I was looking for a Wemos D1 mini v3 case that could also hold a DHT11 sensor and found this one! It works great! I had no issues printing this on my P1S. Instead of soldering the wires to the Wemos board I chose to use the dupont wires. I quickly figured out that if you connect dupont wires to the pins on the Wemos, you will not be able to close the lid. This is ok for now because I'm using this case as a proof of concept. Thank you for designing and sharing this model!

I read somewhere that the smell of peppermint oil is a good deterrent for mice. Not sure if that is true or not but I decided to test that theory with these little passive diffusers. I've printed 5 of them in PETG and stuck 3 cotton balls in each diffuser. I then bought a jar of peppermint oil from Amazon Canada and placed 10 drops on the cotton balls. I've stuck them around my garage in the hope that the mice stopping coming around. Thank you so much for posting this design!

I absolutely love this corner frame ornament. It goes well with my new DIY halloween decoration. I made the picture frame out of trim I bought at Home Depot and then printed out and painted these corner ornaments. Together with the AtomsFX Unliving Portraits digital files, its a perfect fit!

This was my very first print on my new P1S and I think it turned out great!

Its not bulky and it fights perfectly! It's easy to push forward for loading/unloading filament. I definitely recommend this locking AMS saver clip!

Finally a filament clip that is not too bulky and fits perfectly on my Bambu PLA spools as well as my other branded spools.

These dust covers work great in my Cisco switch. I love the friction fit!

I love how this purge bucket is thin but still pretty sturdy. I was looking for a purge bucket that could be used with my P1S and it's anti vibration feet. This does the job perfectly. Thank you so much!

I love the design of this side spool holder. it printed great with my Duramic black PLAthBk you for designing and sharing this print!

I searched high and low for a y splitter that look good and functioned properly without the filament jamming. I am very happy to say that this y splitter is my #1 choice. My filament does not jam while it's being feed through this splitter! Thank you for designing and sharing this print!

This is a very cool phone holder! I love the accent colour on the sides. I do find that the angle is a little to upright for my taste but I still love the design and keep it close by our kitchen table for the kids and I. I printed this with Budget PLA from 3D Printing Canada using the Generic PLA filament profile in Bambu Slicer. Thank you for sharing this design!

I printed this at the request of my daughter. First time printing it, I noticed there were bed adhesion issues. So I cleaned the bed with warm soapy water and viola, it printed! After playing with the dragon scales a few of the scales would come loose. I really like the fact that the scales can be snapped back into place. This is a very cool print! Thank you for sharing!

This spool adapter works perfect for most of my filament rolls. The only brand that had issues fitting this was the Budget PLA from 3D Printing Canada. I highly recommend printing this spool adapter!

I have not had a need to use this yet. A co-worker said this should have been the first thing I printed when I got my new P1S. It's printed now and waits to be used. I printed this with Elegoo Rapid PETG in black.

This nozzle wiper is awesome! So much better then the stock P1S nozzle wiper and I purchased enough tubing (2m) to last me for years. This is one of those designs that should be in your top 10 list of things to print. I printed this in Elegoo Rapid PETG Green. Thank you so much for designing this nozzle wiper as well as the jig for cutting the tub.

This nozzle brush holder with the A1 wiper is great! I printed it on my P1S but using it to clean the nozzle of my Ender 3 v2 Neo. I love this brush so much that I printed a second copy for my niece and her Ender 3 v2 Neo. I used Elegoo Rapid PETG for the filament. Thank you for designing and sharing this brush!