I designed this french cleat hook to be printable without support to hang onto wall cleats (cut out of wood with 45 degrees angle). This is the modular hook and additional attachment can be attached. ie, this tray for wall storage https://makerworld.com/en/models/2878534-modular-tray-94x96mm-internal-dim-french-cleat#profileId-3214668

Model is designed to be used for product photography. The idea is to have diffused lighting for speedlights or continuous video lights. Curved top light box for small item product photography. 3D printed Lightbox design for 130mm (wide) x 130mm (deep) x 70mm (tall) +curvature of top dome. Designed to be able to print even on the a1 mini. I made this as a concept to be able to use LED light panels on the side or top or back with different colours to take some nice photos of small products

3d printed a replacement tightening nut that connects magic arm to clamp. the original arm came with a plastic tightening part that crack and no longer holds the magic arm properly.

made a version two with improved sound. should I add more notes and expand to more keys?!

This design is inspired with an attempted to make a simplified, printable piano hammer mechanism. Instead of hitting music wire, these keys have a contact point that contact three tube/ drums of varying diameters and heights (I was hoping the geometry differences would create more sound differences but it still sounds pretty plastic clicky (at least it makes a good/ satisfying fidget clicker) The three keys snap into their pivot points. I'm open to comments and feedback for ideas of improvement.

This bracket when used with two or more can support 1x6 lumber to make a shelf. There are two holes with counterbore for mounting to the wall and two countersunk screw holes to connect to the 1x6 to fix it into place. Dimensioned and printed in PLA on my A1 mini and it had small clearance to drop in the 1x6 wood with no problems. NOTE: this model have not been weight tested with PLA. I made it primary to hold up some printed models and other small items.

This is a jig that have hole to hole distance of 128mm that works for these Franklin Brass Solid Bar handles (Affiliate link: https://amzn.to/3F09c4B) My wife wanted to install these onto the ikea Oxberg doors that are attached to the billy bookshelves. Since I had multiple to install, I designed this jig to locate to the top of the Oxberg and you hold it in place to drill the two clearance holes to attached the handle.

Designed this Bracket to be able to mount to the wall or any wooden surface, 2x4 or any surfaces you can put two screws. This bracket allows you to hang up a light stand onto the bracket. This allows you to store light stands on the wall/ behind a door or in the example of my picture, behind my table. It keeps the light stand hanging up right and easy to lift up and take out to use. Designed for easy access and storage.

Designed this knob to slide onto the Fender Amp. Bought a used Acoustasonic 15 AMP that was missing a dial so I designed one to slide on. This prints with support which is easily removable with needle nose pliers.

Designed this original to use scrap metal tubes that I had lying around to hold filament. can fit any tube, rod, or wooden dowel that is 28mm in diameter. I also added a 3d printed version that can hold a single spool in case you don't have any metal tubes or other raw materials available.

made this fun emoji keychain on makerlab. Laughing to tears small diameter keychain. LOL emoji or laughing to tears emoji that describes how I feel most of the time with the world events.

Designed this to have sliding rails to store the Ikea Trofast boxes/ trofast bins under tables. The table I ended up mounting my bin was under a small IKEA lack table that I am using as a lego table for my kids. This design allows you to use any counter sink particle board screw or wood screw (depending on your table). I printed the rails vertically (to make sure there is added strength in the loading direction. If you don't care for strength, you can print it lying flat on the print bed. I

I saw these clock repair kits on aliexpress and temu and decided to try designing my own wall clock. It is a simple wall mountable design. Just need to buy a clock mechanism kit (55x55mm) kit and the through hole is a 86mm diameter hole.

This clip on/snap on cold shoe can be attached to 5/8" diameter c-stand booms. There is enough friction not to freely rotate but under heavy weight/ attachment, it can rotate. I attached a RODE wireless GO to transmitter and it holds well in place. I designed this cold shoe mount to attach light accessories onto the cstand. Like wireless transmitters or small led lights. This profile was made in pla but if it was petg or Abs, it might be more durable.

HO HO HO! christmas fidget spinner for friends and family. Perfect stocking stuffer. It is print in place and does not require any support or bearing. ( if you look from the other side… it says oh oh oh so you run if that if you want LOL) This design was generated using a program called: Amazing STL Creator 2 by an awesome creator (not me) Program can be bought on cults3d. https://cults3d.com/en/3d-model/gadget/text-spinners If you use coupon code “CREATENOW” you can get 30% off the program.

STONKS! FIDGET spinner, no bearing required, print in place. Perfect gift for your man in finance, finance bro, day trader friend or significant other. A fun fidget toy off the popular STONKS meme. This design was generated using a program called: Amazing STL Creator 2. This program allows you to generate print in place fidget spinners with custom text. It can be found at https://cults3d.com/en/3d-model/gadget/text-spinners If you use coupon code “CREATENOW” to get 30% off the program.