Slim Wallet (V2) by MakerVerse Designs

MakerVerse Designs

Tools>Gadgets

Print Profile(4)

All

P1S

P1P

X1 Carbon

X1E

A1 mini

0.15mm layer, 3 walls, 15% infill

Designer

2.9 h

3 plates

4.0(17)

A One mini Wallet 0.15mm layer, 3 walls, 15% infill

3.4 h

3 plates

4.3(6)

[Named+Plated] 0.15mm layer, 3 walls, 15% gyroid infill

2.4 h

2 plates

5.0(2)

0.15mm layer, 3 walls, 15% infill

3 h

2 plates

Boost

321

446

508

262

Released

Description

A slim wallet that offers space for 7 cards and a drawer for cash.
I looked for a long time for a wallet that had enough space for cash, but I couldn't find one so I made this one myself.

This ist the Updated Version

I added a lever to securely open and lock the cards so that they don't fall out
I reworked the drawer mechanism so that it lasts better

Important: Some information about printing:

The wallet is printed standing up
First, the WalletConnector and WalletDistributer must be printed. Then the WalletCase.
In the wallet case I added an "pause or M600" command at layer 60 (at layer height 0.15) so that the printing then stops. You have to do this by yourself in your slicer!!!
At Layer 60 the print will stop. Now insert the previously printed WalletConnector and WalletDistributer as in the picture below.
Then you continue the print. The printer will now print over the two parts.
At the end you have to use a little force to free the distributor

Have fun with it and leave a like or subscribe if you like it!

If there are any suggestions for improvement, feel free to write a comment.

Comment & Rating (39)

@benjaminkott

Print Profile

0.15mm layer, 3 walls, 15% infill

Sadly, it is not printable. Support is blocking the insertion of the object.

The designer has replied

@MakerVerse

That's strange... It worked for me and there should actually be enough space. In your picture it looks somehow different than in the slicer. Have you maybe changed something?

(Edited)

@benjaminkott

Replying to @MakerVerse :

I did not change anything, here is a screenshot from the slicer. Bambu Studio - 1.9.1 Public Beta 4

(Edited)

@carboncomputers

Replying to @benjaminkott :

Switching to 'Tree Slim' fixed this issue for me, hope this helps! *note - I'm using Orca slicer 2.0, not Bambu Studio. I had the same issue before making the change, though.

(Edited)

@BenniBiene

Print Profile

0.15mm layer, 3 walls, 15% infill

Version V3 has been released. V3 works great! WASTE OF FILAMENT DONT PRINT THIS

(Edited)

The designer has replied

@MakerVerse

I'm very sorry that it didn't work out for you. Everything went great for me and the wallet has been in use for a few weeks now.

(Edited)

@kennygs

Here a print in place version https://makerworld.com/en/models/464094#profileId-372792

@user_172981332

Printed Great, But.... The little piece (connector?) was too long but I was able to cut it down to fit while it was paused. Biggest issue is trying to figure out how to break free the distributor? Bambu PLA Basic gray Overture PLA Sillk purple EDIT: I was able to get the distributor free but would have been easier if I knew that the tab on the wallet was movable. I thought looking down the wallet that the distributor was printed over and the tab on the wallet was buffer so you didn't hit the distributor. Will have to glue the distributor and the tab. We shall see how it works. Edit: Unfortunately it doesn't fit my wallet contents.

(Edited)

The designer has replied

@MakerVerse

Yes, you need a bit of force to free the distributor

@s5862140

Print Profile

[Named+Plated] 0.15mm layer, 3 walls, 15% gyroid infill

The printing settings this time are fine, but I believe the lowering lever could be designed as a single integrated piece instead of requiring separate parts to be assembled. That would make printing even better.

(Edited)

@WhyNot

Print Profile

A One mini Wallet 0.15mm layer, 3 walls, 15% infill

good but I cannot fit in my pant picked. works great in a coat pockets though

@LeoHobby

I used the stl file. you can forget the 2 separate parts and only print the body and the drawer. and the print was successful.

@Little

leider enttäuscht und dabei sah es auf der Cam so gut aus

@Djsilva17PT

Boosted

Print Profile

0.15mm layer, 3 walls, 15% infill

@zackza

We really needed a wallet like this that has the little card slot for coins/cash,i was going to make a thick card to throw into an existing wallet, id like to try this or even a thinner version that i may customize and add as a profile, ill try printing this on my a1 soon,