vacuum ring for filament vacuum bag

Search models, users, collections, and posts

AYY

Tools>Organizers

IP Report

Print Profile(8)

All

A1 mini

P1S

P1P

X1 Carbon

X1E

H2D

H2D Pro

H2S

P2S

H2C

X2D

A2L

Just 1 Ring 0.2mm layer, 2 walls, 8% infill

Designer

15 min

1 plate

4.9(1.4 k)

filled Base, can be stick to the bag [v2]

Designer

18 min

1 plate

4.9(427)

X4 ARACHNE + 1Layer SLOWED - 0.28mm layer,3 walls,5% infill

38 min

1 plate

4.9(247)

Added a vacuum suction seal against the bag

18 min

1 plate

4.9(246)

Click to see more

Open in Bambu Studio

Boost

4942

14783

2698

1.2 k

16.3 k

12.6 k

Released

Description

help vacuum bag more vacuum

have trouble ring gos around of the bag? just stick [v2] to the bag 👍

note
please Appropriate vacuum level, and keep it on eye, vacuum tooooo hard will bend the spool

[new!] cheak out zipper i made for vacuumbag vacuum bag zipper ↓

Comment & Rating (2698)

@enigmaticFacade

Boosted

These work really well, great job. I made a caddy to hold 10 of them just to keep them organized in my cabinet. Link in case anyone else is interested: https://makerworld.com/en/models/875205#profileId-827818

@chriswood1001

Brilliant! Thanks for the holder link.

@sarendas

Boosted

thanks!

@Thecrazymaker

Boosted

Print Profile

filled Base, can be stick to the bag [v2]

I was using a paper towel folded over as an air gap for my vacuum sealing bags I use for filiment storage. This model was exactly what I was looking for as a permanent, and professional look for my filament storage needs. The print came out great and they work so much better than the paper towel methods. I ended up switching all my filament stored in vacuum storage bags to incorporate this model and ended up printing over 40 of them. Thank you for your contributions to the community.

@krissi1

Print Profile

Just 1 Ring 0.2mm layer, 2 walls, 8% infill

My P1S often drags the filament behind it because it doesn't release from the silicone part, resulting in unsightly flaws as seen on the edge, otherwise I am more than satisfied

The profile uploader has replied

Show original

@enigmaticFacade

Boosted

You dropped a star because of a calibration issue with your printer? That seems absurdly unfair. The model is essentially perfect.

(Edited)

@radish5

Replying to @enigmaticFacade :

They didn’t say they docked the print a star because of their printing issue.

(Edited)

@enigmaticFacade

Boosted

Replying to @radish5 :

Sure… I guess you’re technically correct, but they offered only a single criticism, so it’s a fair assumption. Do you have a different theory?

(Edited)

@vsevolod

Boosted

Print Profile

X4 ARACHNE + 1Layer SLOWED - 0.28mm layer,3 walls,5% infill

Can recommend this top glass handle cover. And it also works for vacuum bags, btw

@AYZSSM

it don't fit in my x1 (sad

@user_317219726

Replying to @AYZSSM :

you can increase xy hole compensation and it probably would. download Orcaslicer and run their calibrations. likely your printer isn't producing dimensionally accurate prints

(Edited)

@Berat3d

Print Profile

filled Base, can be stick to the bag [v2]

It worked. I also designed a storage container compatible with the skadis board.

@ylmz85

Do you have a link to the container for Skadis? Thanks in advance.

(Edited)

@Berat3d

Replying to @ylmz85 :

I uploaded it for you. https://makerworld.com/en/models/1457798-vacuum-ring-container-for-skadish-board

(Edited)

@ylmz85

Replying to @Berat3d :

Thank you! 🙏🏻

(Edited)

@Christophe_01

Print Profile

X4 ARACHNE + 1Layer SLOWED - 0.28mm layer,3 walls,5% infill

Functions flawlessly yet offers no improvement over a null configuration

Show original

@mike.yearwood

incorrect. it is not always easy to pump the air out.

@CBailey629

Replying to @mike.yearwood :

I agree. I used one (the vacuum bag) for the first time yesterday and it was a PIA to get it to start vacuuming

@FreshCityP2S

Replying to @CBailey629 :

that's a shitty vacuum bag. I have found a ton of poor quality vacuum bags have flooded Amazon lately. I bought three different packs from three different sellers and none of them would start vacuuming, not a single bag. I have to carefully poke around in the valve to create a path for the air to escape, and then stick it back down and hope that it stays sealed. Most of them end up holding but it is a huge pain in the ass to do all that messing around for each bag.

@Bobelism

Print Profile

89% size (⌀ 40mm, th 5mm) - 0.2mm layer, 2 walls, 8% infill

thank you! very good model! helps a lot and makes my life easier! i dont struggle anymore to take the air out of the bags like before

@a.lyakhoff

Friend, in the photo, your vacuum cleaner has a square hole, and you made an adapter for it to fit a round hole, right? I need this STL model, please :)

(Edited)

@Bobelism

Replying to @a.lyakhoff :

hi you can find the model on my profile

(Edited)

@user_1754463955

The result is pretty good, but I found that using corrugated cardboard works just as well. Thanks to the creator for the idea!

@xeronn

Print Profile

Just 1 Ring 0.2mm layer, 2 walls, 8% infill

I love them, they work perfectly and speed up the vacuum process. Thanks for sharing.

@Zen_Aku

These are great and I use them all the time. I made a container for them as the existing models I found did not have a secure enough lid. If anyone is interested the link can be found here: https://makerworld.com/en/models/1754119-vacuum-ring-container-with-screw-cap-for-45mm-ring#profileId-1865218

(Edited)

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.